Seagate ST3500414CS Shock, Operating shock, Non-operating shock, Vibration, Operating vibration

Page 22

2.9.5Shock

All shock specifications assume that the drive is mounted securely with the input shock applied at the drive mounting screws. Shock may be applied in the X, Y or Z axis.

2.9.5.1Operating shock

The drives comply with the performance levels specified in this document when subjected to a maximum oper- ating shock of 70 Gs (Read) and 30 Gs (Write) based on half-sine shock pulses of 2 msec. Shocks should not be repeated more than two times per second.

2.9.5.2Non-operating shock

The non-operating shock level that the drive can experience without incurring physical damage or degradation in performance when subsequently put into operation is 350 Gs based on a nonrepetitive half-sine shock pulse of 2 msec duration.

2.9.6Vibration

All vibration specifications assume that the drive is mounted securely with the input vibration applied at the drive mounting screws. Vibration may be applied in the X, Y or Z axis.

2.9.6.1Operating vibration

The maximum vibration levels that the drive may experience while meeting the performance standards speci- fied in this document are specified below

5Hz to 22Hz	0.25 Gs

22Hz to 350Hz	0.50 Gs

350Hz to 500Hz	0.25 Gs

2.9.6.2Non-operating vibration

The maximum non-operating vibration levels that the drive may experience without incurring physical damage or degradation in performance when subsequently put into operation are specified below.

5Hz to 350Hz	3.0 Gs

350Hz to 500Hz	3.0 Gs

16	Video 3.5 HDD Product Manual, Rev. J

Image 22

Contents Video 3.5 HDD Revision history Revision Date Sheets affected or commentsPipeline HD.2 Series Sata Product Manual, Rev. J Pipeline HD.2 Series Sata Product Manual, Rev. J Contents Pipeline HD.2 Series Sata Product Manual, Rev. J Introduction About the Serial ATA interface Drive specifications Specification summary tablesDrive specifications summary for 1000GB models Drive specification ST31000424CS ST31000322CSVideo 3.5 HDD Product Manual, Rev. J Drive specifications summary for 500 and 320GB models Video 3.5 HDD Product Manual, Rev. J Drive specifications summary for 250 and 160GB models Drive specification ST3250412CS ST3250312CS ST3160316CSVideo 3.5 HDD Product Manual, Rev. J Formatted capacity Default logical geometryLBA mode Recording and interface technologySeek time Physical characteristicsStart/stop times Power specifications Conducted noise Typical current profilesVoltage tolerance Idle mode Power management modesActive mode Sleep modeEnvironmental specifications Non-operating shock ShockOperating shock VibrationElectromagnetic immunity Drive A-weighted Sound Power Levels SWL, BAAcoustics emissions Test for Prominent Discrete Tones PDTsAgency certification Safety certificationReliability Annualized Failure Rate AFRAustralian C-Tick N176 Korean RRLFCC verification Corrosive environment Environmental protectionChina Restriction of Hazardous Substances RoHS Directive Configuring and mounting the drive Handling and static-discharge precautionsConfiguring the drive Serial ATA cables and connectorsMounting dimensions for 1000GB models Drive mountingMounting dimensions for 500, 320, 250 and 160GB models Serial ATA Sata interface Hot-Plug compatibilitySignal Serial ATA device plug connector pin definitionsSerial ATA connector pin definitions Pin Function DefinitionSupported ATA commands Supported ATA commandsCommand name Command code in hex F3H Identify Device command Word Description ValueXx07H Description if bit is set to Bit Word Bit WordIdle Immediate command with Iunload faeture is supported Set Features command Set Features command valuesM.A.R.T. commands 3 S.M.A.R.T. commandsCode in features register A.R.T. command Seagate Technology support services Data Recovery Services Authorized Service Centers Warranty ServiceData Recovery Services Call Center Toll-free Direct dial Index RRL Page Video 3.5 HDD Product Manual, Rev. J Page Seagate Technology LLC

Related manuals

Manual 50 pages 5.86 Kb