Seagate ST336918N, ST318418N, ST318438LW, ST336938LW manual Input characteristics, LVD output signals

Page 79

Barracuda 36ES2 Product Manual, Rev. B

69

Output characteristics

Each signal (Vs) driven by LVD interface drivers shall have the following output characteristics when measured at the disc drive connector:

Steady state Low level output voltage* = –.95 V = < Vs = < –1.55 V (signal negation/logic 0)
Steady state High level output voltage* = –.95 V = < Vs = < 1.55 V (signal assertion/logic 1)

					voltage		ranges 0.700 V = < Vcm = < 1.800 V.

Differential voltage = +0.6 V minimum with common-mode
*These voltages shall be measured between the output terminal and							the SCSI device’s logic ground reference.



The output characteristics shall additionally conform to EIA RS-485.

Figure 22. LVD output signals

Input characteristics

Each signal (Vs) received by LVD interface receiver circuits shall have the following input characteristics when measured at the disk drive connector:

Steady state Low level output voltage* = 0.030 V = < Vs = < 3.6 V (signal negation/logic 0) Steady state High level output voltage* = –3.6 V = < Vs = < –0.030 V (signal assertion/logic 1)

Differential voltage = +0.30 V minimum with common-mode voltage ranges 0.700 V = < Vcm = < 1.800 V. (X3T10/1302D)

*These voltages shall be measured between theoutput terminal and theSCSI device’s logic ground reference.

Input characteristics shall additionally conform to EIARS-485-983.

Figure 23. Typical SE-LVD alternative transmitter receiver circuits

Image 79

Contents Product Manual, Volume Page Product Manual, Volume Page Revision Date Writer/Engineer Sheets Affected Revision status summary sheetPage Contents Interface requirements Defect and error managementInstallation Seagate Technology support servicesBarracuda 36ES2 Product Manual, Rev. B Vii List of FiguresPage Barracuda 36ES2 family drive ST336938LW shown ScopeBarracuda 36ES2 Product Manual, Rev. B Applicable standards and reference documentation Korean MIC Australian C-TickTaiwanese Bsmi General description Reliability Standard featuresMedia characteristics PerformanceOptions factory installed Factory installed accessoriesProgrammable drive capacity Performance characteristics Start/stop time Ultra2 Scsi Ultra160 ScsiPrefetch/multi-segmented cache control Caching write data Cache operationPrefetch operation Barracuda 36ES2 Product Manual, Rev. B Reliability specifications Service philosophy Reliability and servicePreventive maintenance Service lifeControlling S.M.A.R.T 7 S.M.A.R.TPredictive failures Performance impactReporting control Determining rateInvoking DST State of the drive prior to testingDST Failure Definition ImplementationLog page entries Product warrantyShort test Function Code 001b Extended test Function Code 010bProduct repair and return information Barracuda 36ES2 Product Manual, Rev. B AC power requirements Physical/electrical specificationsDC power requirements Conducted noise immunity Power sequencing3 12 V Current profile +5 Volt Current during spindle start Typical Amper es Amps Power dissipation ST336938/ST318438 Barracuda 36ES2 Product Manual, Rev. B ST336918/ST318418 Environmental limits TemperatureShock Barracuda 36ES2 Product Manual, Rev. B Relative humidityEffective altitude sea level Shock and vibrationRecommended mounting Barracuda 36ES2 Product Manual, Rev. B Vibration Air cleanlinessAcoustics Dimension Table Mechanical specificationsMounting configuration dimensions Barracuda 36ES2 Product Manual, Rev. B Drive error recovery procedures Defect and error managementDrive internal defects Scsi systems errors Drive ID/option select header InstallationConfigure drive options FormattingDo not install jumpers retain cover J6 jumper header for N model J5 jumper header on LW models only J2 option select header for LW models Barracuda 36ES2 Product Manual, Rev. B Barracuda 36ES2 Product Manual, Rev. B Function description Cooling Drive orientationAir flow Grounding Barracuda 36ES2 Product Manual, Rev. B Drive mountingBarracuda 36ES2 Product Manual, Rev. B Scsi interface messages supported Interface requirementsScsi interface commands supported Commands supported by Barracuda 36ES2 family drives Barracuda 36ES2 Product Manual, Rev. B Vendor ID Firmware numbers page C0h Inquiry Vital Product dataUnit serial number page 80h Implemented operating definition page 81hJumper settings page C2h Mode Sense data DEF CHG Barracuda 36ES2 Product Manual, Rev. B Condition/features supported Supported Status supported 2 REQ/ACK offset DC cable and connectorPhysical interface Model drive physical interface 50-pin Scsi I/O connector Pin Power Scsi interface cable requirements Scsi interface physical descriptionMating connectors for N model drives Barracuda 36ES2 Product Manual, Rev. B Mating connectorsScsi daisy chain interface cabling for N drives Nonshielded 68 pin Scsi device connector used on LW drives Scsi daisy chain interface cabling for LW drives GND GND DBP1 +DBP1 Electrical description Multimode signalsMultimode-SE and LVD alternatives LVD output signals Input characteristicsSingle-ended drivers/receivers for LW models Transmitter characteristicsReceiver characteristics Single-ended drivers/receivers for N modelsLow voltage differential I/O circuits General cable characteristicsTerminator requirements Terminator power DrivesLW drives Page Following table provides drive activity LED status Drive activity LEDTechnical Support Seagate Technology support services Online ServicesAutomated Services Presales SupportUSA/Canada/Latin America Support Services Customer Service CSOEuropean Support Services Asia/Pacific Support Services Africa/Middle East Support ServicesCall Center Toll-free Direct dial Barracuda 36ES2 Product Manual, Rev. B Index Diffsens LED PCB System chassis Barracuda 36ES2 Product Manual, Rev. B