Western Telematic SRM-100 manual General Parameters Menu, Super, Esc

Page 20

SRM-100 - Secure Rack Modem, User's Guide

Set-Up and Configuration

 

 

GENERAL PARAMETERS:

 

1.

System

Password:

SUPER

2.

Console

 

Port

Password:

(undefined)

3.

System

Dial

Back #:

(undefined)

4.

Site

ID:

 

 

 

(undefined)

5.

Real-Time-Clock

Thu 03/08/2001 14:14:04

6.

Console

 

Port

Communication:

9600,N,8,1

7.

Command

 

Echo:

On

8.

No

Activity

Timeout:

5 Min.

9.

Password

 

Attempts:

3

10. Password on Dial Back:

Off

11.

Security

 

Mode:

On

12.

Audit

Log

Options:

All

13.

Dial

Back

Attempts:

1

14.

Dial

Back

Delay

30 Sec.

Enter

Selection,

 

 

Press

<ESC>

 

to abort ...

 

 

 

 

 

 

 

 

 

 

Figure 5.2: The General Parameters Menu

5.2. The General Parameters Menu

To access the General Parameters menu (Figure 5.2), activate the command mode, then type /G [Enter]. To change parameters, key in the number for the desired item, press [Enter], then follow the instructions in the submenu.

1.System Password: This password protects access to the Command Mode. When a caller connects to the SRM, a password prompt is sent. If the System Password is entered at this prompt, the caller will be granted access to the Command Mode. Note that the System Password is case sensitive.

(Up to 16 characters, Default = SUPER).

Notes:

•If the System Password is deleted or cleared, remote access (via modem) to the SRM Command Mode will be disabled.

•The same password can be defined for both the System Password and the Console Password.

•The System Password cannot be the same as a defined User Password. If you attempt to define a System Password that is the same as an existing User Password, an error message will be sent.

5-3

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Users Guide Firmware Version 1.13 and HigherTable of Contents List of Figures OperationPassword Protected Access IntroductionFeatures Typographic ConventionsUnit Description Front PanelPower Switch Back PanelGetting Started Applying Power to the UnitConnecting a PC to the Console Port Communicating with the SRM-100 Commands Modem Port SettingsMT2834ZPX ATZSRM-100 Secure Rack Modem, Users Guide Hardware Installation Rack Mounting InstallationConnecting Power to the SRM-100 AC Powered UnitsDefault Modem Baud Rate Sw1, Sw2 SetUp SwitchesDC Powered Units Default Rings to Answer Sw5 Default Flow Control Format Sw3Default Bits and Parity Sw4 Default Security Mode Status Sw8 Default ARQ/Compression Status Sw6Default Modem Speaker Status Sw7 Initialize Unit to Default Settings Cable ConnectionModem Port Console PortTelco Line Access Via the Console Port Set-Up and ConfigurationCommand Mode Access Access via Modem General Parameters Menu General ParametersSuper ESCSet-Up and Configuration SRM-100 Secure Rack Modem, Users Guide DTR Modem Parameters MenuModem Parameters SRM-100 Secure Rack Modem, Users Guide Save Parameters Password Directory Edit Password DirectoryAdd Name / Password EDIT/DELETE NAME/PASSWORD Edit / Delete from ListEdit / Delete from Search Viewing the Password Directory Password Directory Sample Data ShownZero Activity Counters SRM Operating Modes Password FunctionsOperation User Passwords System PasswordConsole Port Password Password on Dial Back Dial Back NumbersSuppressing the Confirmation Prompt Dialing Out from the Modem PortViewing the Audit Log Audit LogSRM-100 Secure Rack Modem, Users Guide Delete Entire Password Directory Utilities MenuZero All Activity Counters Delete Audit LogUpload Parameters Default ParametersSend Test Message Pass-Through Mode Console-Modem Download ParametersSaving and Restoring Parameters and Password Directory Sending Parameters to a FileRestoring Saved Parameters Modem Port Interface DescriptionsConsole Port Specifications CompatibilityCustomer Service Trademark and Copyright InformationIndex Index-1Index-2 Index-3
Top Page Image Contents