Western Telematic SRM-100 manual Default Parameters, Send Test Message, Upload Parameters

Page 39

SRM-100 - Secure Rack Modem, User's Guide

Operation

7.6.4. Default Parameters

This option allows the system administrator to reset the unit to default parameters without deleting the Password Directory. To clear all menu selected parameters except the Password Directory, and return the SRM-100 to its default configuration, first access the Utilities Menu as described in Section 7.6. When the Utilities menu appears, type 4, press [Enter], and follow the instructions in the submenu.

Notes:

•When the SRM-100 is reset to default parameters, all menu-selected parameters will be cleared. Menu selected parameters cannot be recovered unless they have been saved to an ASCII text file as described in Section 8.

•When the "Default Parameters" function is performed via modem, the SRM will not immediately reset modem parameters. The unit will reset all other parameters, wait for the caller to disconnect, and then reset modem parameters.

7.6.5. Send Test Message

This option allows the system administrator to send a test message via the Console Port or telecommunications line. If the SRM Command Mode has been accessed via the Console Port, the Test Message will be sent out the Console Port; if the Command Mode has been accessed via modem, the Test Message will be sent via the telecommunications line.

This Test Message is used to test communication with a remote device that has accessed the SRM Command Mode via modem, or to test communication with the local device connected to the Console Port. To send the Test Message, proceed as follows:

1.Access the SRM Command Mode as described in Section 5.1.

2.When the "SRM>" command prompt appears, type /U and press [Enter] . The Utilities Menu will appear as shown in Figure 7.2.

3.From the Utilities Menu, type 5 and press [Enter] .

a)If you have accessed the SRM Command Mode via the Console Port, the Test Message will then be sent out the Console Port.

b)If you have accessed the SRM Command Mode via modem, the Test Message will then be sent out the telecommunications line.

4.To terminate the Test Message, press the [Esc] key.

7.6.6. Upload Parameters

This function is used to restore SRM parameters that have been saved to an ASCII text file using the Utilities Menu's "Download Parameters" function. To restore saved SRM parameters, please refer to the instructions in Section 8.2.

7-8

Page 38 Page 40
Image 39
Page 38 Page 40
Contents Firmware Version 1.13 and Higher Users GuideTable of Contents Operation List of FiguresIntroduction Password Protected AccessTypographic Conventions FeaturesFront Panel Unit DescriptionBack Panel Power SwitchApplying Power to the Unit Connecting a PC to the Console PortGetting Started Communicating with the SRM-100 ATZ CommandsModem Port Settings MT2834ZPXSRM-100 Secure Rack Modem, Users Guide AC Powered Units Hardware InstallationRack Mounting Installation Connecting Power to the SRM-100SetUp Switches DC Powered UnitsDefault Modem Baud Rate Sw1, Sw2 Default Flow Control Format Sw3 Default Bits and Parity Sw4Default Rings to Answer Sw5 Default ARQ/Compression Status Sw6 Default Modem Speaker Status Sw7Default Security Mode Status Sw8 Console Port Initialize Unit to Default SettingsCable Connection Modem PortTelco Line Set-Up and Configuration Command Mode AccessAccess Via the Console Port Access via Modem ESC General Parameters MenuGeneral Parameters SuperSet-Up and Configuration SRM-100 Secure Rack Modem, Users Guide Modem Parameters Menu Modem ParametersDTR SRM-100 Secure Rack Modem, Users Guide Save Parameters Edit Password Directory Password DirectoryAdd Name / Password Edit / Delete from List EDIT/DELETE NAME/PASSWORDEdit / Delete from Search Password Directory Sample Data Shown Viewing the Password DirectoryZero Activity Counters Password Functions OperationSRM Operating Modes System Password Console Port PasswordUser Passwords Dial Back Numbers Password on Dial BackDialing Out from the Modem Port Suppressing the Confirmation PromptAudit Log Viewing the Audit LogSRM-100 Secure Rack Modem, Users Guide Delete Audit Log Delete Entire Password DirectoryUtilities Menu Zero All Activity CountersDefault Parameters Send Test MessageUpload Parameters Download Parameters Pass-Through Mode Console-ModemSending Parameters to a File Saving and Restoring Parameters and Password DirectoryRestoring Saved Parameters Interface Descriptions Console PortModem Port Compatibility SpecificationsTrademark and Copyright Information Customer ServiceIndex-1 IndexIndex-2 Index-3
Top Page Image Contents