Western Telematic MT9234, MT5634 manual Delayed

Page 30

MT5634/MT9234 Modem; AT Command Set

Terse	Verbose	Description
80	CONNECT 52000	Connected at 52000 bps
81	CONNECT 54000	Connected at 54000 bps
82	CONNECT 56000	Connected at 56000 bps
83	CONNECT 58000	Connected at 58000 bps
84	CONNECT 60000	Connected at 60000 bps
86	CONNECT 16800	Connected at 16800 bps
87	CONNECT 115200	Connected at 115200 bps
88	DELAYED	Delay is in effect for the dialed number
89	BLACKLISTED	Dialed number is blacklisted
90	BLACKLIST FULL	Blacklist is full
91	CONNECT 230400	Connected at 230400 bps
100	CONNECT 28000	Connected at 28000 bps
101	CONNECT 29333	Connected at 29333 bps
102	CONNECT 30666	Connected at 30666 bps
103	CONNECT 33333	Connected at 33333 bps
104	CONNECT 34666	Connected at 34666 bps
105	CONNECT 37333	Connected at 37333 bps
106	CONNECT 38666	Connected at 38666 bps
107	CONNECT 41333	Connected at 41333 bps
108	CONNECT 42666	Connected at 42666 bps
109	CONNECT 45333	Connected at 45333 bps
110	CONNECT 46666	Connected at 46666 bps
111	CONNECT 49333	Connected at 49333 bps
112	CONNECT 50666	Connected at 50666 bps
113	CONNECT 53333	Connected at 53333 bps
114	CONNECT 54666	Connected at 54666 bps
115	CONNECT 25333	Connected at 25333 bps
116	CONNECT 26666	Connected at 26666 bps

*EC is added to these result codes when the extended result codes conﬁguration option is enabled. EC is replaced by one of the following codes, depending on the type of error control connection:

•V42bis – V.42 error control (LAP-M) and V.42bis data compression

•V42 – V.42 error control (LAP-M) only

•MNP5 – MNP 4 error control and MNP 5 data compression

•MNP4 – MNP 4 error control only

•NoEC – No error control protocol

5-2

Image 30

Contents AT Command Set MT5634/MT9234Page Table of Contents MT5634/MT9234 Modem AT Command Set Introduction MT5634/MT9234 Modem AT Command Set AT Command Summary DescriptionAtmtsmodemcr AT Commands Command En Echo Command Mode Characters Command Ds DialCommand DS=y Dial Stored Telephone Number Command Fn Echo Online Data CharactersCommand M n Monitor Speaker Mode Command H n Hook ControlCommand I n Information Request Command N n Modulation HandshakeCommand Sr=n Set Register Value Command P Pulse DialingCommand Qn Result Codes Enable/Disable Command Sr? Read Register ValueCommand Zn Modem Reset Command Result Code OptionsCommand Result Code Selection Command Data Carrier Detect DCD ControlCommand &Fn Load Factory Settings Command &Dn Data Terminal Ready DTR ControlCommand &En XON/XOFF Pacing Control Command &Gn V.22bis Guard Tone ControlCommand &Qn Asynchronous Communications Mode Command Leased Line OperationCommand Pulse Dial Make-to-Break Ratio Selection Command Data Set Ready DSR ControlCommand &Wn Store Current Conﬁguration Command &Tn Loopback Test V.54 Test CommandsCommand &V Display Current Settings Command &Zy=x Store Dialing CommandCommand \A n Command \B n Transmit BreakCommand \K n Break Control Command \Tn Inactivity Timer Command \Nn Error Correction Mode SelectionCommand \Qn Flow Control Selection Command \Vn Protocol Result CodeCommand %An Adaptive Answer Result Code Enable Command \Xn XON/XOFF Pass-ThroughCommand Data Calling Tone Command View Numbers in BlacklistCommand %Hn Direct Connect Enable Command %DCn AT Command ControlCommand Fallback and Fall Forward Control Command Cisco ConﬁgurationCommand $RP n Ring Priority vs. AT Command Priority Command $EB n Asynchronous Word LengthCommand $MB n Online BPS Speed Command $SB n Serial Port Baud RateCommand +VDR=x, y Distinctive Ring Report Command #CBAn Callback AttemptsCommand #CBDn Callback Delay Command #CBIn Local Callback Inactivity Timer Command #CBF? Callback Failed Attempts DisplayCommand #CBFR Callback Failed Attempts Reset Command #CBNy=xCommand #Sx Enter Setup Password Command #CBSn Callback Enable/DisableCommand #Pn Set 11-bit Parity Command #S=x Store Setup PasswordRegister Unit Range Default Description RegistersS37 Decimal Registers MT5634/MT9234 Modem AT Command Set Result Codes Terse Verbose DescriptionDelayed Remote Configuration and Country Code Configuration Example %%%ATMTSMODEMChanging the Setup Password Country Code Configuration MT5634/MT9234 Modem AT Command Set Page Sterling Irvine California 949 586-9950 Toll Free

Related manuals

Manual 36 pages 4.51 Kb