Tyan Computer TYAN S1668 user manual Hardware Specifications/Features

Page 4

1.2 Hardware Specifications/Features

wCPU

Intel Pentium Pro 150 thru 200 MHz (Socket 8)

 

(Single or Dual CPU configuration)

wCoprocessor

On-chip floating point unit

wSpeed

60/66 MHz system bus

 

30/33 MHz PCI bus

 

7.5/8.33 MHz ISA bus speed

w DRAM

4 double banks of 72 pin SIMM sockets

 

Supports 5V or 3.3V memory

 

Supports BEDO(Burst Extended Data Out)

 

Supports EDO(Extended Data Out) DRAMs

 

Supports ECC(Error Correcting Code)w/ parity

 

Supports Fast Page Mode DRAMs

 

Supports 8MB to 1024MB of DRAMs

wL2 Cache

256/512KB 2nd level cache in CPU

wEIDE Controller

Primary and secondary PCI EIDE channels on

 

board for support of up to four EIDE Mode 0

 

through Mode 4 drives.Supports DMA mode 1

 

and 2.

wEnhanced I/O

Multi-mode bi-directional parallel port that

 

supports standard, EPP and ECP modes.

 

Supports 16550 compatible UARTS for on-board

 

high speed serial ports.

 

Support for an IrDA compliant InfraRed inter-

 

face.

 

On-board floppy controller.

 

On-board USB(Universal Serial Port).

wMouse

On-board PS/2 mouse connector.

wI/O Bus Slots

5 Master/Slave PCI-Bus

 

3 ISA Bus (One ISA and one PCI shared slot)

S1668-ATX-001 http://www.tyan.com

4

Image 4
Contents Tyan S1668 Dual Pentium Pro ATX 440FX PCI-ISA System Board Table Of Contents Introduction Hardware Specifications/Features Software Specifications EnvironmentBoard Installation On Board Resource Setting .1 S1668 ATX Board Layout VRM1Jumper Settings CPU Speed J27, J21, J22, J23, and J24 Cmos Resest/Password Reset J41Default offDram Voltage J2, J3, J14, J15, J4, J5, J16 and J17Default CPU Clock Multiplier J21, J22, J23 and J24Turbo Switch J47 Non-Turbo Mode Not Supported Speaker Connector J43 Keylock Connector J44Selection J28 & J29 Reset Connector J45 Turbo LED Connector J42Flash Eeprom J32Default InfraRed Interface Con4 and Con5Soft Power On Switch J1 CPU FAN Power J49 and J50 Speaker Connector InstallationTurbo Switch Turbo LED Connector InstallationHardware Reset Switch Connector Installation Refer to for Flash Eeprom upgrade proceduresDram Installation Voltage ID for Older Pentium Pro CPUs J10 and J20Memory Table Bank0 Bank1 Bank2 Bank3 TotalCPU Installation Peripheral Device Installation VRM InstallationConnecting the Power Supply & On/Off Switch Bios Configuration Entering SetupControl Keys Setup Page menu/Option Page Setup Menu Getting Help Main MenuStandard Cmos setup Bios features setupChipset features setup Power Management setupDate Standard Cmos Setup MenuTime Primary/Secondary Drive type Drive a type/Drive B typeHalt On VideoMemory Expanded Memory Other MemoryBoot Sequence Swap Floppy Drive Default value is DisabledVirus warning CPU Internal Cache/External CacheBoot Up Floppy Seek Boot Up NumLock Status Default value is OnChipset Features Setup Power Management ROM ISA Bios Power Management Setup Award SOFTWARE, INCStandby Mode Doze ModePower Down Activities PCI Slot Configuration Resources Controlled By IRQ n assigned toLegacy ISA PCI/ISA PnPIntegrated Peripherals Load Setup Defaults ROM ISA Bios Cmos Setup Utility Award SOFTWARE, INC IDE HDD Auto Detection Flash Writer Utility Page Flash Memory Writer Utility Screen Award Flash Memory WriterTimer & DMA Channel MAP System Resources