VXI SM8000 user manual SM8001 / SM8002 Multi Switch Specifications, PDL6

Page 17

VXI Technology, Inc.

SM8001 / SM8002 MULTI SWITCH SPECIFICATIONS

GENERAL SPECIFICATIONS

WAVELENGTH RANGE

	780 – 1650 nm
INSERTION LOSS2
	0.6 dB typical, 1.2 dB maximum
BACK REFLECTION
Single-Mode Fiber3	-60 dB typical, - 55 dB maximum
Multi-Mode Fiber3	-20 dB typical

SWITCHING TIME4

300 ms + 16 ms per channel maximum

ISOLATION

-80 dB maximum

DURABILITY

10 million cycles minimum

REPEATABILITY5

±0.03 dB maximum

PDL6

0.05 dB maximum

OPERATING TEMPERATURE

0°C – 50°C

STORAGE TEMPERATURE

-20°C – 70°C

HUMIDITY

40°C / 90% Relative Humidity / 5 days

Notes

1All specifications referenced without connectors.

2Measured at 23°C ± 5°C.

3Based on standard 1-meter pigtail length.

4Based on BUSY output pulse. Actual optical switching time may be faster.

5Sequential repeatability for 100 cycles at constant temperature after warm-up.

6Measured at 1550 nm, single-mode only.

SM8000 Series Introduction

17

Image 17

Contents SM8000 Series VXI Technology, Inc Table of Contents Control Modes VXI Technology, Inc SM8000 Series Preface Certification Steve Mauga, QA Manager EMCVXI Technology, Inc SM8000 Series Preface Terms and Symbols Service should only be performed by qualified personnelAvoid Electric Shock Support Resources VXI Technology, Inc SM8000 Series Preface Overview Section SM8000 Series Optical Switch Controller Configurations SM8001 / SM8002 MULTI-CHANNELSWITCHESDuplex 1 x N PDL6 SM8001 / SM8002 Multi Switch SpecificationsSpdt SM8003 Prism SwitchesPDL3 SM8003 Prism Switch SpecificationsPDL SM8101 / SM8102 Optical AttenuatorsIntroduction Calculating System Power and Cooling RequirementsSetting the Chassis Backplane Jumpers MSB LSB Setting the Logical AddressExample Selecting the Extended Memory Space Optical Connections Cleaning Optical ConnectorsMating Optical Connectors General Description SM8001 / SM8002 Multi-Channel SwitchesSM8003 Prism Switches SM8003 Prism SwitchesSM8101 / SM8102 Optical Attenuators Attenuator DiagramRelay Registers Output Channel Selection Resetting the SwitchOperation N Switch Configuration Common Active Channel Duplex 1 x N Switch ConfigurationN Blocking Switch Configuration N Non-Blocking Switch Configuration 8MULTI-SWITCH Timing Calculating Switching TimeSM8003 Prism Switches Control Modes Starting the DeviceUncalibrated Operation Move-To-Absolute-Step Calibrated OperationError Status Busy SignalResetting the Device Commanding the DevicesAddressing Register AccessOffset Write Function Smip II Register MAP A16Logical Address Register Write Only ID Register Read OnlyDevice Type Register Read Only Status Register Read OnlyOffset Register Read and Write Control Register Write OnlySerial Number High Register Read Only Serial Number Low Register Read OnlySubclass Register Read Only Interrupt Status Register Read OnlyInterrupt Control Register Read and Write NVM Access Register Write NVM Access Register ReadBoard X, Y Used Address Register Read and Write Trace RAM Start High Register Read and WriteTrace RAM End Low Register Read and Write Trace RAM End High Register Read and WriteTrace RAM Address High Register Read and Write Trace RAM Address LOW Register Read and WriteTTL Trigger Polarity Register Write Only Open Trigger Select Register Write OnlyBusy Trigger Control Register Read and Write Trace RAM Control Register Read and WriteReserved Registers Read and Write Trigger Advance Register Write OnlyBoard Busy Register Read Only 1MB RAM Control Register Read and Write See Typical Optical Multi Switch OperationControl Register Delay Register Read and Write Plug-In LA+0x104 Command Register Write Only Address Register Write Only Relay Register Offset Device MemoryWriting to the Relay Registers Relay Register 00 Read and WriteRegister 0A thru 0C Read Relay Optical Module’s Data Attenuation LevelRegister 02 thru 08 Read and Write Programming Examples Typical Optical MULTI-SWITCH Control ExampleWrite Typical Optical Attenuator Control ExampleVXI Technology, Inc Read Example Write ExampleCommand Transmit Data Receive Data Byte Byte Count Command SET31h 30h35h 32h80h 6Ch82h 81h89h 83h8Bh 8Ah8Dh 8Ch8Eh Convert to hexadecimal 90hRecommends That the Optical MODULE’S A2h 96hVXI Technology, Inc SM8000 Series Programming Index VXIbus