NETGEAR WG511U user manual Verify wireless connectivity to your network, LED Descriptions

Page 25

User’s Manual for the NETGEAR Double 108 Mbps Wireless PC Card 32-bit CardBus WG511U

Verify wireless connectivity to your network.

a.Verify that your Connection and Status Monitor information matches your wireless network.

b.Check the two LEDs on the WG511U:

Table 3-1:

LED Descriptions

 

 

 

 

 

LED 1

LED 2

 

 

(below the

(below the

Meaning

 

word

word

 

NETGEAR

NETGEAR

 

 

on the left)

on the right)

 

 

Slow blink

OFF

Power save mode (default from power up or reset)

 

 

 

 

 

Alternate

Alternate

Looking for network association

 

blink

blink

Power LED goes ON; Network LED is OFF; then Power

 

 

 

LED goes OFF and Network LED goes ON

 

 

 

 

 

Slow blink

Slow blink

Associated or joined with network; no activity

 

 

 

 

 

Fast blink

Fast blink

Associated or joined with network; blink rate increases

 

 

 

with activity on the network over the air or locally on the

 

 

 

network

c. Verify connectivity to the Internet or network resources.

Note: If you are unable to connect, see troubleshooting tips in the Basic Installation section of the Reference Manual on the NETGEAR Double 108 Mbps Wireless PC Card 32-bit CardBus WG511U Resource CD.

Basic Setup

3-7

August 2004

Image 25
Contents August Technical Support FCC Information to User Export Restrictions Contents Chapter Wireless Security Configuration Glossary Contents Audience, Conventions, Publication Date Chapter About This ManualHtml version of this manual How to Navigate this ManualHow to Print this Manual About This Manual Chapter Introduction Key Features and Related Netgear ProductsWhat’s in the Box? 802.11a and 802.11b/g Wireless NetworkingRoad Map for How to Get There From Here Road Map for ‘How to Get There From Here’Netgear Double Exchange files Use printers What You Need Before You Begin Chapter Basic SetupVerifying System Requirements Observing Location and Range Guidelines Two Basic Operating ModesWG511U Default Wireless Configuration Settings For Windows XP Users Installing a WG511U Basic Installation InstructionsClick Install Driver and Utility Basic Setup Wireless Security Configuration Configure your WG511ULED Descriptions Verify wireless connectivity to your networkFor Windows 2000 & 98/Me Users Installing a WG511U Found New Hardware Wizard Profile Configure your WG511U and saveBelow Word Meaning Interpreting the LED on the WG511U WG511U Wireless Connection IndicatorsColor Condition Description Interpreting System Tray Icon ColorsBasic Tips TroubleshootingTroubleshooting Frequently Asked Questions Basic Setup Understanding the Configuration Options Chapter Netgear Smart Wireless WizardUsing Configuration Profiles Connecting to an Access Point in Infrastructure Mode Run the WG511U Smart Wireless Wizard How to Configure an Infrastructure Mode ProfileConfigure the wireless network settings Save your settings in a ProfileNetgear WG511U Wireless PC Card in Computer-to-Computer Mode Connecting to Another PC in Ad-hoc ModeConfigure the PC network settings How to Configure an Ad-hoc Mode NetworkAd-Hoc Setting What’s on the Statistics Page? Understanding the Advanced Settings Understanding the Security Options Chapter Wireless Security ConfigurationBasic Requirements for WEP Using WEP SecurityWireless Network Name Ssid WEP Security Settings WorksheetWEP Security Encryption Key Configure the Network Name Ssid settings How to Configure WEP Encryption SecurityConfigure the WEP settings Basic Requirements for WPA-PSK Using WPA-PSK Advanced SecurityHow to Configure WPA-PSK Advanced Security WPA-PSK Security Settings WorksheetWPA-PSK settings screen Configure the WPA-PSK settingsWireless Security Configuration FCC, CE Appendix a Technical SpecificationsTechnical Specifications Wireless Networking Overview Appendix B Wireless Networking BasicsInfrastructure Mode Network Name Extended Service Set Identification Essid Ad Hoc Mode Peer-to-Peer WorkgroupWireless Channels 802.11b/g Wireless Channels 802.11a Legal Power Output and Wireless Channels WG511U user can use thirteen channels in non-turbomode WPA Wireless Security OverviewWEP Overview WEP Authentication802.1x Cisco LeapAuthentication Open System Steps Bit WEP WEP KeysWEP Key Configuration How to Use WEP Parameters802.1x Port Based Network Access Control Figure B-4 802.1x authentication WPA Wireless Security How Does WPA Compare to WEP? How Does WPA Compare to Ieee 802.11i? What are the Key Features of WPA Security?Figure B-5 WPA Overview Figure B-6 WPA/802.1x Authentication Sequence Wireless Networking Basics Temporal Key Integrity Protocol Tkip WPA Data Encryption Key ManagementMichael Product Support for WPA Is WPA Perfect?AES Support Wireless network adapters Wireless client programs Wireless Networking Basics Configuring Windows 98 and Me for TCP/IP Networking Appendix C Preparing Your PCs for Network AccessInstall or Verify Windows Networking Components Preparing Your Computers for TCP/IP NetworkingPreparing Your PCs for Network Access Locate your Network Neighborhood icon Choose Settings, and then Control PanelPrimary Network Logon is set to Windows logon Verifying TCP/IP Properties Selecting Windows’ Internet Access MethodConfiguring Windows 2000 or XP for TCP/IP Networking Dhcp Configuration of TCP/IP in Windows XP Dhcp Configuration of TCP/IP in Windows XP orTCP/IP details are presented on Support tab Verify that Obtain an IP address Dhcp Configuration of TCP/IP in WindowsRight click on Local Area Connection and select Properties Obtain an IP address automatically is selected Verifying TCP/IP Properties for Windows XP or Preparing Your PCs for Network Access List of Glossary Terms GlossaryAdsl EAP Internet service provider Megabits per second Ssid WEP Glossary Numerics Index
Related manuals
Manual 2 pages 10.78 Kb