NETGEAR GS748TS-100NAS, GS748TNA user manual Manually Assigning Network Parameters

Page 19

GS748T Software User Manual

Manually Assigning Network Parameters

If your network has no DHCP service, you must assign a static IP address to your switch. If you choose, you can assign it a static IP address even if your network has DHCP service. Proceed as follows:

1.Connect the GS748T Smart Switch to your existing network.

2.Power on the switch by plugging in the power cord (Default IP is 192.168.0.239).

3.Install the Smart Wizard Discovery Utility program on your computer

4.Start the Smart Wizard Discovery utility.

5.Click Discover for the Smart Wizard Discovery Utility to find your GS748T Smart Switch. You should see a screen similar to that shown in Figure 2-1 on page 2-1.

6.Click on Configuration Setting. A screen similar to that shown below appears.

Figure 2-3

7.Choose Disable for DHCP.

8.Enter your chosen switch IP address, gateway IP address and subnet mask, and then type your password and click “Set”. Please ensure that your PC and the GS748T Smart Switch are in the same subnet. Make a note of these settings for later use.

Getting Started—Smart Wizard Discovery

2-3

v2.0, April 2007

Image 19
Contents NETGEAR, Inc Bestätigung des Herstellers/Importeurs TrademarksStatement of Conditions Certificate of the Manufacturer/ImporterEurope EU Declaration of Conformity Regulatory Compliance InformationFCC Information to User FCC Requirements for Operation in the United StatesGS748T Smart Switch Product and Publication Details Contents Appendix a Specifications and Default Values Appendix C Network Cabling V2.0, April About This Manual How to Use This BookWho Should Use this Book Bold Conventions, Formats and ScopeHtml Manual Navigation How to Print this ManualDocument Date Version Description Part Number Revision HistorySwitch Management Interface Chapter Switch Management OverviewSystem Requirements Switch Management MethodsNetwork with Dhcp server Getting Started-Smart Wizard DiscoveryNetwork without Dhcp Server Manually Assigning Network Parameters V2.0, April Password Change Web AccessAdditional Utilities Firmware Upgrade Exit V2.0, April Starting Web Management Chapter Basic Web ManagementNetgear Home Page and Switch Status V2.0, April Description of Switch Status Parameters V2.0, April System Functions Firmware Menu Managing System Files-Backup and RestoreTo restore saved settings Factory ResetTo back up files Logout Resetting the SystemV2.0, April Using the Switch Configuration Utility Chapter Configuring the SwitchPort Configuration Viewing Packet Statistics V2.0, April Port-based QoS Regulating Traffic Rates using Quality of Service SettingsIeee 802.1p-based QoS Differentiated Services Code Point DSCP-based QoS Vlan Adding and Configuring Ieee 802.1Q Vlan Groups Reconfiguring an Ieee 802.1Q Vlan Group Reconfiguring a Port-based Vlan Adding and Configuring Port-based VLANsSelecting a Management Vlan Creating Port Trunks to Increase Link BandwidthSetting up Port Trunks Removing Port Trunks Using a Sniffer Port to Monitor TrafficControlling Per-port Packet Throughput Jumbo Frame SupportStorm Control Dropping Traffic that is Flooding a Port Using Spanning Tree Protocol to Prevent Path LoopsV2.0, April V2.0, April Enabling Switch Management using Snmp To Add a MAC Address Controlling Switch Access by MAC Address and Vlan IDFiltering Unknown Multicast Packets Using Igmp Snooping to Route Packets Based on ContentTo Remove a MAC Address from the Table Setting Up Static Multicast Groups V2.0, April GS748T Smart Switch Specifications Appendix a Specifications and Default ValuesTable A-3. Port Characteristics GS748T Smart Switch Features and DefaultsTable A-8. Other Features Smart Wizard Enabled Statistics Per port Appendix B Virtual Local Area Networks VLANs Example Ieee 802.1Q VLANsPort-based VLANs Port-based Vlan Example ConfigurationResults of this Configuration Fast Ethernet Cable Guidelines Appendix C Network CablingCategory 5 Cable Twisted Pair Cables Category 5 Cable SpecificationsFigure C-1Straight-Through Twisted-Pair Cable Patch Panels and CablesCabling Using 1000BASE-T Gigabit Ethernet over Category 5 CableLength Near End Cross Talk NextReturn Loss Patch Cables RJ-45 Plug and RJ-45 ConnectorsConclusion V2.0, April