NETGEAR GS748TS-100NAS Patch Panels and Cables, Figure C-1Straight-Through Twisted-Pair Cable

Page 67

GS748T Software User Manual

Figure C-1Straight-Through Twisted-Pair Cable

Figure C-2illustrates crossover twisted pair cable.

Figure C-2Crossover Twisted-Pair Cable

Patch Panels and Cables

If you are using patch panels, make sure that they meet the 100BASE-TX requirements. Use Category 5 UTP cable for all patch cables and work area cables to ensure that your UTP patch cable rating meets or exceeds the distribution cable rating.

To wire patch panels, you need two Category 5 UTP cables with an RJ-45 plug at each end, as shown in Figure C-3.

Network Cabling

C-3

v2.0, April 2007

Image 67
Contents NETGEAR, Inc Bestätigung des Herstellers/Importeurs TrademarksStatement of Conditions Certificate of the Manufacturer/ImporterEurope EU Declaration of Conformity Regulatory Compliance InformationFCC Information to User FCC Requirements for Operation in the United StatesGS748T Smart Switch Product and Publication Details Contents Appendix a Specifications and Default Values Appendix C Network Cabling V2.0, April About This Manual How to Use This BookWho Should Use this Book Bold Conventions, Formats and ScopeHtml Manual Navigation How to Print this ManualDocument Date Version Description Part Number Revision HistorySwitch Management Interface Chapter Switch Management OverviewSystem Requirements Switch Management MethodsNetwork with Dhcp server Getting Started-Smart Wizard DiscoveryNetwork without Dhcp Server Manually Assigning Network Parameters V2.0, April Password Change Web AccessAdditional Utilities Firmware Upgrade Exit V2.0, April Starting Web Management Chapter Basic Web ManagementNetgear Home Page and Switch Status V2.0, April Description of Switch Status Parameters V2.0, April System Functions Firmware Menu Managing System Files-Backup and RestoreTo restore saved settings Factory ResetTo back up files Logout Resetting the SystemV2.0, April Using the Switch Configuration Utility Chapter Configuring the SwitchPort Configuration Viewing Packet Statistics V2.0, April Port-based QoS Regulating Traffic Rates using Quality of Service SettingsIeee 802.1p-based QoS Differentiated Services Code Point DSCP-based QoS Vlan Adding and Configuring Ieee 802.1Q Vlan Groups Reconfiguring an Ieee 802.1Q Vlan Group Reconfiguring a Port-based Vlan Adding and Configuring Port-based VLANsSelecting a Management Vlan Creating Port Trunks to Increase Link BandwidthSetting up Port Trunks Removing Port Trunks Using a Sniffer Port to Monitor TrafficControlling Per-port Packet Throughput Jumbo Frame SupportStorm Control Dropping Traffic that is Flooding a Port Using Spanning Tree Protocol to Prevent Path LoopsV2.0, April V2.0, April Enabling Switch Management using Snmp To Add a MAC Address Controlling Switch Access by MAC Address and Vlan IDFiltering Unknown Multicast Packets Using Igmp Snooping to Route Packets Based on ContentTo Remove a MAC Address from the Table Setting Up Static Multicast Groups V2.0, April GS748T Smart Switch Specifications Appendix a Specifications and Default ValuesTable A-3. Port Characteristics GS748T Smart Switch Features and DefaultsTable A-8. Other Features Smart Wizard Enabled Statistics Per port Appendix B Virtual Local Area Networks VLANs Example Ieee 802.1Q VLANsPort-based VLANs Port-based Vlan Example ConfigurationResults of this Configuration Fast Ethernet Cable Guidelines Appendix C Network CablingCategory 5 Cable Twisted Pair Cables Category 5 Cable SpecificationsFigure C-1Straight-Through Twisted-Pair Cable Patch Panels and CablesCabling Using 1000BASE-T Gigabit Ethernet over Category 5 CableLength Near End Cross Talk NextReturn Loss Patch Cables RJ-45 Plug and RJ-45 ConnectorsConclusion V2.0, April