NETGEAR GS748TS-100NAS, GS748TNA user manual Viewing Packet Statistics

Page 37

GS748T Software User Manual

Speed: Indicates the communication mode set for the port. The default setting for all ports is Auto-negotiation (Auto). The possible entries are:

Auto: Auto-negotiation

100M Full: 100 Mbps full duplex

100M Half: 100 Mbps half duplex

10M Full: 10 Mbps full duplex

10M Half: 10 Mbps half duplex

Disable

Flow Control: may be set on for Flow Control support or off for no flow control.

Default Priority: This value indicates the default traffic priority f or the port in the implementation of Port-based Quality of Service (QoS). The values may be set to 0 - 7.

Note: In order for it to work, you must map the priority to the appropriate 4 queues in the IEEE802.1P of Switch > QoS page.

To activate the new settings, click Apply.

Note: Speed must be set to the same value as for the port’s link partner. If this is not done, packet loss or link errors may occur.

Viewing Packet Statistics

This page shows reports of packet traffic and packet errors. The table headings meanings are explained as follows:

ID: The port number on the switch

Tx: Transmitted packets

Rx: Received packets

Tx Error: Transmitted packets with error. Packets are counted as contributing to TX Error if they:

Had a late collision detected during the transmission (512 bit-times into the transmission)

Experienced 16 failed transmission attempts due to collision.

Were dropped due to lack of resources

Configuring the Switch

4-3

v2.0, April 2007

Image 37
Contents NETGEAR, Inc Statement of Conditions TrademarksCertificate of the Manufacturer/Importer Bestätigung des Herstellers/ImporteursEurope EU Declaration of Conformity Regulatory Compliance InformationFCC Information to User FCC Requirements for Operation in the United StatesGS748T Smart Switch Product and Publication Details Contents Appendix a Specifications and Default Values Appendix C Network Cabling V2.0, April About This Manual How to Use This BookWho Should Use this Book Bold Conventions, Formats and ScopeHtml Manual Navigation How to Print this ManualDocument Date Version Description Part Number Revision HistorySwitch Management Interface Chapter Switch Management OverviewSystem Requirements Switch Management MethodsNetwork with Dhcp server Getting Started-Smart Wizard DiscoveryNetwork without Dhcp Server Manually Assigning Network Parameters V2.0, April Password Change Web AccessAdditional Utilities Firmware Upgrade Exit V2.0, April Starting Web Management Chapter Basic Web ManagementNetgear Home Page and Switch Status V2.0, April Description of Switch Status Parameters V2.0, April System Functions Firmware Menu Managing System Files-Backup and RestoreTo restore saved settings Factory ResetTo back up files Logout Resetting the SystemV2.0, April Using the Switch Configuration Utility Chapter Configuring the SwitchPort Configuration Viewing Packet Statistics V2.0, April Port-based QoS Regulating Traffic Rates using Quality of Service SettingsIeee 802.1p-based QoS Differentiated Services Code Point DSCP-based QoS Vlan Adding and Configuring Ieee 802.1Q Vlan Groups Reconfiguring an Ieee 802.1Q Vlan Group Reconfiguring a Port-based Vlan Adding and Configuring Port-based VLANsSelecting a Management Vlan Creating Port Trunks to Increase Link BandwidthSetting up Port Trunks Removing Port Trunks Using a Sniffer Port to Monitor TrafficControlling Per-port Packet Throughput Jumbo Frame SupportStorm Control Dropping Traffic that is Flooding a Port Using Spanning Tree Protocol to Prevent Path LoopsV2.0, April V2.0, April Enabling Switch Management using Snmp To Add a MAC Address Controlling Switch Access by MAC Address and Vlan IDFiltering Unknown Multicast Packets Using Igmp Snooping to Route Packets Based on ContentTo Remove a MAC Address from the Table Setting Up Static Multicast Groups V2.0, April GS748T Smart Switch Specifications Appendix a Specifications and Default ValuesTable A-3. Port Characteristics GS748T Smart Switch Features and DefaultsTable A-8. Other Features Smart Wizard Enabled Statistics Per port Appendix B Virtual Local Area Networks VLANs Example Ieee 802.1Q VLANsPort-based VLANs Port-based Vlan Example ConfigurationResults of this Configuration Fast Ethernet Cable Guidelines Appendix C Network CablingCategory 5 Cable Twisted Pair Cables Category 5 Cable SpecificationsFigure C-1Straight-Through Twisted-Pair Cable Patch Panels and CablesCabling Using 1000BASE-T Gigabit Ethernet over Category 5 CableLength Near End Cross Talk NextReturn Loss Patch Cables RJ-45 Plug and RJ-45 ConnectorsConclusion V2.0, April