NETGEAR GS748TNA, GS748TS-100NAS user manual V2.0, April

Page 38

GS748T Software User Manual

•Rx Error: Received packet/s with error. Packets are counted as contributing to RX Error if they:

•Were less than 64 bytes or greater than 1522 bytes in size

•Had a bad FCS

•Were dropped due to lack of resources.

1.Click on Statistics in the main menu; a Statistics page appears.

2.Click on the Refresh button at the top of the page to obtain current statistics data

3.Click Clear Counters to start a new statistics count over time.

4.Click on a port ID entry; the individual statistics table for the port is displayed. This table breaks down statistics in more detail as shown in the following diagram.

Figure 4-8

4-4

Configuring the Switch

v2.0, April 2007

Page 37 Page 39
Image 38
Page 37 Page 39
Contents NETGEAR, Inc Certificate of the Manufacturer/Importer TrademarksStatement of Conditions Bestätigung des Herstellers/ImporteursRegulatory Compliance Information Europe EU Declaration of ConformityFCC Requirements for Operation in the United States FCC Information to UserGS748T Smart Switch Product and Publication Details Contents Appendix a Specifications and Default Values Appendix C Network Cabling V2.0, April Who Should Use this Book How to Use This BookAbout This Manual Conventions, Formats and Scope BoldHow to Print this Manual Html Manual NavigationRevision History Document Date Version Description Part NumberChapter Switch Management Overview Switch Management InterfaceSwitch Management Methods System RequirementsGetting Started-Smart Wizard Discovery Network with Dhcp serverNetwork without Dhcp Server Manually Assigning Network Parameters V2.0, April Additional Utilities Web AccessPassword Change Firmware Upgrade Exit V2.0, April Chapter Basic Web Management Starting Web ManagementNetgear Home Page and Switch Status V2.0, April Description of Switch Status Parameters V2.0, April System Functions Managing System Files-Backup and Restore Firmware MenuTo back up files Factory ResetTo restore saved settings Resetting the System LogoutV2.0, April Chapter Configuring the Switch Using the Switch Configuration UtilityPort Configuration Viewing Packet Statistics V2.0, April Ieee 802.1p-based QoS Regulating Traffic Rates using Quality of Service SettingsPort-based QoS Differentiated Services Code Point DSCP-based QoS Vlan Adding and Configuring Ieee 802.1Q Vlan Groups Reconfiguring an Ieee 802.1Q Vlan Group Adding and Configuring Port-based VLANs Reconfiguring a Port-based VlanCreating Port Trunks to Increase Link Bandwidth Selecting a Management VlanSetting up Port Trunks Using a Sniffer Port to Monitor Traffic Removing Port TrunksJumbo Frame Support Controlling Per-port Packet ThroughputUsing Spanning Tree Protocol to Prevent Path Loops Storm Control Dropping Traffic that is Flooding a PortV2.0, April V2.0, April Enabling Switch Management using Snmp Controlling Switch Access by MAC Address and Vlan ID To Add a MAC AddressTo Remove a MAC Address from the Table Using Igmp Snooping to Route Packets Based on ContentFiltering Unknown Multicast Packets Setting Up Static Multicast Groups V2.0, April Appendix a Specifications and Default Values GS748T Smart Switch SpecificationsGS748T Smart Switch Features and Defaults Table A-3. Port CharacteristicsTable A-8. Other Features Smart Wizard Enabled Statistics Per port Appendix B Virtual Local Area Networks VLANs Ieee 802.1Q VLANs ExamplePort-based Vlan Example Configuration Port-based VLANsResults of this Configuration Category 5 Cable Appendix C Network CablingFast Ethernet Cable Guidelines Category 5 Cable Specifications Twisted Pair CablesPatch Panels and Cables Figure C-1Straight-Through Twisted-Pair CableUsing 1000BASE-T Gigabit Ethernet over Category 5 Cable CablingReturn Loss Near End Cross Talk NextLength RJ-45 Plug and RJ-45 Connectors Patch CablesConclusion V2.0, April
Top Page Image Contents