Lightwave Communications SCS3230 manual Device Cards, Access Cards, Network / Control Card

Page 19

A Lantronix Company

SCS3230 System Administrator's Guide

3.2Device Cards

The Device cards are fully compatible with the SCS3230 application. The SCS3230 requires version 4.03 Build 01 (or higher) of the Device Card binary firmware. Firmware updates are downloadable from the Lightwave FTP site (ftp://ftp.lightwavecom.com).

Note: DEVICE CARD firmware MUST be updated to 4.03 or higher

Each DEVICE card has four completely independent ports for attachment to servers or other devices with console ports. Eight device cards may be installed per system, for a maximum of 32 device ports. The device ports do not send an 'break' signal to the attached servers at any time unless specified by the user. There are no adjustments directly on the device cards. All parameters are set up through the system administrator port.

3.3Access Cards

The card configuration is changed with the SCS3230, compared to CS3200.

3.3. 1 NETWORK / CONTROL Card

The NETWORK / CONTROL card allows users to connect to the device cards from an SSH or telnet session over an IP network, and remote access to the administration functions.

The NETWORK / CONTROL card replaces the CONTROL card from the CS3200, and is located in the far right slot of the system chassis. Only one card is required in an SCS3230.

The NETWORK / CONTROL card includes one TERM connector for a local Console; one 10/100 NET connector for a TCP/IP network interface, and four CHANNEL EXTENDER ports. The Channel Extender ports are connected by RJ45 cables to one to four CHANNEL EXTENDER cards, which are an extension of the NETWORK card's operation.

The NETWORK / CONTROL card supports up to sixteen simultaneous user

telnet connections and one administrator connection to the same IP address. The network card must be connected to a network that uses TCP/IP.

15.00.038

- 19 -

May 2002

Image 19

Contents SCS3230 Lightwave Communications, Inc. LCI, a Lantronix Company Copyright & TrademarkDate Rev Comments Disclaimer & RevisionsManufacturer’s Name & Address Declaration of ConformityProduct Description SCS3230 Setup Script and System Administration User Access and Interface For Your Notes Quick Start Product DescriptionSystem Features Upgrade DescriptionHardware Features Flash 3230 Network/Control CardLantronix Company 1 10/100 Port Network Term Port Console Backup and Restore CommandsConnections System OverviewConnect Up to Thirty-two RS-232C Compatible Ports 128K Fifo Audit TrailInterface Security Passwords3200 Chassis Power Supply Module2 3200 Switch Cards System ComponentsDevice Cards Access CardsNetwork / Control Card Terminal Cards Channel Extender Cards4 3200 Network Cards Modem Card 5 3200 10/100 Network CardsItems in a SCS3230 Kit Installation InstructionsRestore Procedure Backup Procedure of your CS3200 SystemMove Database from your CS3200 to SCS3230 To Restore from a 3200 to a LCI Update To Update a Card or CardsConnecting to the Term Port DCE Connecting Equipment to the SCS3230Terminal Card TermModem Card Network / Control CardSUN Device CardConsoleServer 3200 System ConsoleServer 3200 Adapter Quick Checklist General layout showing Device port numbering SCS3230 Setup Script and System Administration Power-up Sequence Basic Use of the Administrator Functions Logging In, Network Connection Logging In, Serial ConnectionLogging Out Help Screen System Help Command ListSave AbbreviationsSys Admin vs. root access Setup Script Hostname and IP Address ConsoleServer 3200 System Lantronix Company Timezone Clock Lantronix Company Configure DNS Lantronix Company Hosts Services Syslog SSH Logins Telnet logins NTP Daemon Configure the Firewall ConsoleServer 3200 System Ping Attempts Firewall Reject MethodConsoleServer 3200 System Confirm Changes Save Command Adding a User ID Creating and Managing UsersDevice Device Device Device Device Device Device Device Listing User IDs Editing a User IDConsoleServer 3200 System Listusers Deleting a User IDStop Bits Terminals Command Modem Command Connections Command Status CommandsVersion Command Listcards CommandInfo Command LOG Command Powerstatus CommandSys Admin Session Management Commands Breaking User Connections Linesperpage CommandForcelogout Command Break CommandTelnettimeout Command Network Card User Access and InterfaceBye Command Logged OUT Help Overview of CommandsMonitor A.K.A. Device Mode Help F2 PULL-DOWN Menu Showing Initial Menu Choices Logging In and Changing PasswordsChecking Connections Logging OutConnection Info Screen F2 PULL-DOWN Menu to Select a Device PORT, Part Selecting a Device PortF2 PULL-DOWN Menu to Listen to a Device Port Part Listening to a Server SessionF2 PULL-DOWN Menu to Listen to a Device Port Part Direct Mode Escape Sequence Direct ModeF2 PULL-DOWN Menu for Device A.K.A. Monitor Mode Using the BufferDisplay Previous Goto Beginning of BufferGoto END of Buffer Display NextLantronix Company F2 PULL-DOWN Menu to Change Break Sequence Break Generation SequenceF2 PULL-DOWN Menu to Display System Info Displaying System InformationFront Panel Display Information Lantronix Company ConsoleServer 3200 System Panel 10 press down Panel 11 press down Appendix a Command Abbreviations Connections Appendix B Hexadecimal Ascii Code Equivalent