Nvidia 2 manual Installing Nvidia Quadro G-Sync II Card

Page 14

NVIDIA Quadro G-Sync II

Installing NVIDIA

Quadro G-Sync II Card

Before you begin, make sure that the Quadro FX 4600 and/or Quadro FX 5600 graphics board and NVIDIA drivers are correctly installed.

The following is additional information concerning installation of the NVIDIA Quadro G-Sync II card.

Note: The NVIDIA Quadro G-Sync II option card must be used only in conjunction with an NVIDIA Quadro FX 4600 or an NVIDIA Quadro FX 5600 graphics board.

1.Install the Quadro G-Sync II option card into any available expansion slot within six inches of the G-Sync connector on the appropriate Quadro FX 4600 and/or Quadro FX 5600 graphics board.

2.Use the cable that comes with your Quadro G-Sync II option card to connect the primary G-Sync connector to the Quadro FX graphics board G-Sync connector shown on page 8.

7

Image 14

Contents 176-0002-000 Page Page Nvidia Quadro G-Sync Page Table of Contents References and Resources Introduction to Nvidia Quadro G-Sync About This GuideNvidia Quadro G-Sync II User Guide System Requirements Implementing SLI TechnologyNvidia Frame Synchronization UnpackingNvidia Quadro G-Sync II Equipment Two 2 Ribbon CablesSafety Instructions Installing Nvidia Quadro G-Sync II Card Quadro G-Sync Nvidia Frame Synchronization Under Windows XP How To Set Up Genlock Set Up the HardwareVID IA Q uadro G-Sync Onnector Bracket Sync Source Server Set Up the Software Basic Genlock SetupDetecting the House Sync Signal Click OK to save the settingsUsing the House Sync Signal Under The synchronization pulses are based on, clickOu tgo in g Sync trigg ered from lead in g and falling ed ge Viewing the Connection Status How To Set Up Frame LockRestoring an Unstable Display Er ver Click Apply Set Up the Server SoftwareBasic Server Setup Changing the Timing Signal Frequency Click Edit Settings to open the Server Settings dialog boxSet Up the Client Software Basic Client SetupIntroducing a Timing Delay at Client Systems Yn c D elay SkewSwap Sync Setup Setting Up Genlock + Frame Lock Checking the Connection Status Swap Sync Nvidia Quadro G-Sync II User Guide Nvidia Frame Synchronization Under Linux Using the nvidia-settings Utility Nvidia Q uadro G-Sync Connector Bracket Syn c Sou rce Go to the nvidia-settingsframe lock panel An X Server is typically speciﬁed in the format systemmSynchronizing to the External House Signal Ou tgo in g Sync trigg ered from lead in g and falling ed ge Understanding the Status Indicators Sync and Connection Status for the Genlock Server Four frame locked systems An X Server is typically speciﬁed in the format systemm Test the Connections Sync and Connection Status for the Server Check the Use House Sync if Present check box Leveraging Frame Lock Genlock in OpenGL Frame Lock RestrictionsSupported Frame Lock Conﬁgurations ‰ Frame Lock + SLI SFR, AFR, or Sliaa Two Quadros, SingleGeneral Steps Sample ConﬁgurationsGenlock Example Make sure frame lock sync is disabledQuery the enabled displays on the Quadro Check that the refresh rate is the one we wantEnable framelocking Enable use of the house sync signalConﬁgure the house sync signal video mode Toggle the test signal‰ First display from system Disable frame lockFrame Lock Example Enable frame lock on server Query the enabled displays on the QuadrosDisable the house sync signal on the master device Check the refresh rate is the same for all displaysEnable frame lock on slave devices Make sure frame lock is disabled for all QuadrosVerify that the refresh rate is the same for all displays Writing a Frame Lock Client for NV-CONTROL 1.8 and earlier Enable frame lock on the slave devicesWriting a Frame Lock NV-CONTROL Client Node Most likely, you want Are using a house sync. Most likely, you wantFramelocksyncdisable on each X screen to disable frame lock Writing a Frame Lock Client for NV-CONTROL 1.9 and later Query the number of Quadro G-Sync II devices on Querying the Frame Lock Capabilities of a SystemConﬁguring the Frame Lock Group Quadro G-Sync II device Most likely, you wantEnabling/Disabling Frame Lock Using a house sync. Most likely, you wantEnable frame lock on each Quadro by setting Nvctrlframelock Nvidia Quadro G-Sync II User Guide Using the OpenGL Extensions Key Points and Deﬁnitions Frame Synchronization Using the OpenGL ExtensionsAbout Buffer Swaps Buffer Swap Criteria Window Buffer SwapsConﬁguring Swap Groups Conﬁguring for Swap SyncFrame Counter ‰ To bind a group to a barrier, call OpenGL ExtensionsConﬁguring Swap Barriers This call binds a swap group to a barrier WglJoinSwapGroupNV, glxJoinSwapGroupNVWglBindSwapBarrierNV GlxBindSwapBarrierNV WglQuerySwapGroupNV GlxQuerySwapGroupNV WglQueryMaxSwapGroupsNV GlxQueryMaxSwapGroupsNVWglResetFrameCountNV,glxResetFrameCount WglQueryFrameCountNV,glxQueryFrameCountGetting Driver Updates Nvidia Quadro G-Sync II User Guide Registration, Support Warranty Registering Your Quadro SyncWarranty and Support Compliance and Certiﬁcations Copyright