Nvidia 2 manual Using the House Sync Signal, Under The synchronization pulses are based on, click

Page 21

NVIDIA Quadro G-Sync II User Guide

Using the House Sync Signal

This section describes how to:

Select which edge of the house sync signal to use as the trigger

Double the trigger frequency from the house sync signal

Properly handle interlaced house sync signals

Introduce a timing delay to the house sync signal

1.From the NVIDIA Control Panel Select a Task pane, under Workstation, click Synchronize Displays.

2.Make sure that the On this system radio button under The timing server is selected.

3.Open the Server Settings dialog box using one of the following methods:

From the Synchronize Displays page, click Edit Settings, or

From the NVIDIA Control Panel navigation tree pane, under Workstation, click View System Topology, then right click the display icon that is

designated to be the server and click

Server Settings

4.Under The synchronization pulses are based on, click the

An external house sync signal radio button. The Server Settings dialog box will show the incoming house sync frequency. A frequency of 0.00 Hz indicates that the system has not yet been set as the server.

14

Image 21

Contents 176-0002-000 Page Page Nvidia Quadro G-Sync Page Table of Contents References and Resources About This Guide Introduction to Nvidia Quadro G-SyncNvidia Quadro G-Sync II User Guide Implementing SLI Technology System RequirementsUnpacking Nvidia Frame SynchronizationTwo 2 Ribbon Cables Nvidia Quadro G-Sync II EquipmentSafety Instructions Installing Nvidia Quadro G-Sync II Card Quadro G-Sync Nvidia Frame Synchronization Under Windows XP Set Up the Hardware How To Set Up GenlockVID IA Q uadro G-Sync Onnector Bracket Sync Source Server Basic Genlock Setup Set Up the SoftwareClick OK to save the settings Detecting the House Sync SignalUnder The synchronization pulses are based on, click Using the House Sync SignalOu tgo in g Sync trigg ered from lead in g and falling ed ge How To Set Up Frame Lock Restoring an Unstable DisplayViewing the Connection Status Er ver Set Up the Server Software Basic Server SetupClick Apply Click Edit Settings to open the Server Settings dialog box Changing the Timing Signal FrequencyBasic Client Setup Set Up the Client SoftwareYn c D elay Skew Introducing a Timing Delay at Client SystemsSwap Sync Setup Setting Up Genlock + Frame Lock Checking the Connection Status Swap Sync Nvidia Quadro G-Sync II User Guide Nvidia Frame Synchronization Under Linux Using the nvidia-settings Utility Nvidia Q uadro G-Sync Connector Bracket Syn c Sou rce An X Server is typically speciﬁed in the format systemm Go to the nvidia-settingsframe lock panelSynchronizing to the External House Signal Ou tgo in g Sync trigg ered from lead in g and falling ed ge Understanding the Status Indicators Sync and Connection Status for the Genlock Server Four frame locked systems An X Server is typically speciﬁed in the format systemm Test the Connections Sync and Connection Status for the Server Check the Use House Sync if Present check box Frame Lock Restrictions Leveraging Frame Lock Genlock in OpenGL‰ Frame Lock + SLI SFR, AFR, or Sliaa Two Quadros, Single Supported Frame Lock ConﬁgurationsSample Conﬁgurations General StepsQuery the enabled displays on the Quadro Make sure frame lock sync is disabledGenlock Example Check that the refresh rate is the one we wantConﬁgure the house sync signal video mode Enable use of the house sync signalEnable framelocking Toggle the test signalDisable frame lock Frame Lock Example‰ First display from system Disable the house sync signal on the master device Query the enabled displays on the QuadrosEnable frame lock on server Check the refresh rate is the same for all displaysMake sure frame lock is disabled for all Quadros Enable frame lock on slave devicesVerify that the refresh rate is the same for all displays Enable frame lock on the slave devices Writing a Frame Lock NV-CONTROL ClientWriting a Frame Lock Client for NV-CONTROL 1.8 and earlier Are using a house sync. Most likely, you want Framelocksyncdisable on each X screen to disable frame lockNode Most likely, you want Writing a Frame Lock Client for NV-CONTROL 1.9 and later Conﬁguring the Frame Lock Group Querying the Frame Lock Capabilities of a SystemQuery the number of Quadro G-Sync II devices on Quadro G-Sync II device Most likely, you wantUsing a house sync. Most likely, you want Enable frame lock on each Quadro by setting NvctrlframelockEnabling/Disabling Frame Lock Nvidia Quadro G-Sync II User Guide Using the OpenGL Extensions Frame Synchronization Using the OpenGL Extensions About Buffer SwapsKey Points and Deﬁnitions Window Buffer Swaps Buffer Swap CriteriaConﬁguring for Swap Sync Frame CounterConﬁguring Swap Groups OpenGL Extensions Conﬁguring Swap Barriers‰ To bind a group to a barrier, call WglJoinSwapGroupNV, glxJoinSwapGroupNV WglBindSwapBarrierNV GlxBindSwapBarrierNVThis call binds a swap group to a barrier WglQueryMaxSwapGroupsNV GlxQueryMaxSwapGroupsNV WglQuerySwapGroupNV GlxQuerySwapGroupNVWglQueryFrameCountNV,glxQueryFrameCount WglResetFrameCountNV,glxResetFrameCountGetting Driver Updates Nvidia Quadro G-Sync II User Guide Registering Your Quadro Sync Registration, Support WarrantyWarranty and Support Compliance and Certiﬁcations Copyright