Nvidia 2 manual Query the enabled displays on the Quadros, Set the master display device CRT-0

Page 53

NVIDIA Quadro G-Sync II User Guide

1.Query the enabled displays on the Quadros.

nvidia-settings -q myserver:0[gpu:0]/EnabledDisplays

nvidia-settings -q myserver:0[gpu:1]/EnabledDisplays

nvidia-settings -q myslave1:0[gpu:0]/EnabledDisplays

nvidia-settings -q myslave1:0[gpu:1]/EnabledDisplays

3.Check the refresh rate is the same for all displays.

nvidia-settings -q myserver:0[gpu:0]/RefreshRate

nvidia-settings -q myserver:0[gpu:1]/RefreshRate

nvidia-settings -q myslave1:0[gpu:0]/RefreshRate

nvidia-settings -q myslave1:0[gpu:1]/RefreshRate

4.Make sure the display device we want as master is masterable

nvidia-settings -q myserver:0[gpu:0]/ FrameLockMasterable

5.Set the master display device (CRT-0).

nvidia-settings -a myserver:0[gpu:0]/FrameLockMaster= 0x00000001

6.Disable the house sync signal on the master device.

nvidia-settings -a myserver:0[framelock:0]/ FrameLockUseHouseSync=0

7.Set the slave display devices.

nvidia-settings -a myserver:0[gpu:1]/FrameLockSlaves= 0x00000001

nvidia-settings -a myslave1:0[gpu:0]/FrameLockSlaves= 0x00000001

nvidia-settings -a myslave1:0[gpu:1]/FrameLockSlaves= 0x00000001

8.Enable frame lock on server.

nvidia-settings -a myserver:0[gpu:0]/ FrameLockEnable=1

46

Image 53

Contents 176-0002-000 Page Page Nvidia Quadro G-Sync Page Table of Contents References and Resources About This Guide Introduction to Nvidia Quadro G-SyncNvidia Quadro G-Sync II User Guide Implementing SLI Technology System RequirementsUnpacking Nvidia Frame SynchronizationTwo 2 Ribbon Cables Nvidia Quadro G-Sync II EquipmentSafety Instructions Installing Nvidia Quadro G-Sync II Card Quadro G-Sync Nvidia Frame Synchronization Under Windows XP Set Up the Hardware How To Set Up GenlockVID IA Q uadro G-Sync Onnector Bracket Sync Source Server Basic Genlock Setup Set Up the SoftwareClick OK to save the settings Detecting the House Sync SignalUnder The synchronization pulses are based on, click Using the House Sync SignalOu tgo in g Sync trigg ered from lead in g and falling ed ge Viewing the Connection Status How To Set Up Frame LockRestoring an Unstable Display Er ver Click Apply Set Up the Server SoftwareBasic Server Setup Click Edit Settings to open the Server Settings dialog box Changing the Timing Signal FrequencyBasic Client Setup Set Up the Client SoftwareYn c D elay Skew Introducing a Timing Delay at Client SystemsSwap Sync Setup Setting Up Genlock + Frame Lock Checking the Connection Status Swap Sync Nvidia Quadro G-Sync II User Guide Nvidia Frame Synchronization Under Linux Using the nvidia-settings Utility Nvidia Q uadro G-Sync Connector Bracket Syn c Sou rce An X Server is typically speciﬁed in the format systemm Go to the nvidia-settingsframe lock panelSynchronizing to the External House Signal Ou tgo in g Sync trigg ered from lead in g and falling ed ge Understanding the Status Indicators Sync and Connection Status for the Genlock Server Four frame locked systems An X Server is typically speciﬁed in the format systemm Test the Connections Sync and Connection Status for the Server Check the Use House Sync if Present check box Frame Lock Restrictions Leveraging Frame Lock Genlock in OpenGL‰ Frame Lock + SLI SFR, AFR, or Sliaa Two Quadros, Single Supported Frame Lock ConﬁgurationsSample Conﬁgurations General StepsQuery the enabled displays on the Quadro Make sure frame lock sync is disabledGenlock Example Check that the refresh rate is the one we wantConﬁgure the house sync signal video mode Enable use of the house sync signalEnable framelocking Toggle the test signal‰ First display from system Disable frame lockFrame Lock Example Disable the house sync signal on the master device Query the enabled displays on the QuadrosEnable frame lock on server Check the refresh rate is the same for all displaysMake sure frame lock is disabled for all Quadros Enable frame lock on slave devicesVerify that the refresh rate is the same for all displays Writing a Frame Lock Client for NV-CONTROL 1.8 and earlier Enable frame lock on the slave devicesWriting a Frame Lock NV-CONTROL Client Node Most likely, you want Are using a house sync. Most likely, you wantFramelocksyncdisable on each X screen to disable frame lock Writing a Frame Lock Client for NV-CONTROL 1.9 and later Conﬁguring the Frame Lock Group Querying the Frame Lock Capabilities of a SystemQuery the number of Quadro G-Sync II devices on Quadro G-Sync II device Most likely, you wantEnabling/Disabling Frame Lock Using a house sync. Most likely, you wantEnable frame lock on each Quadro by setting Nvctrlframelock Nvidia Quadro G-Sync II User Guide Using the OpenGL Extensions Key Points and Deﬁnitions Frame Synchronization Using the OpenGL ExtensionsAbout Buffer Swaps Window Buffer Swaps Buffer Swap CriteriaConﬁguring Swap Groups Conﬁguring for Swap SyncFrame Counter ‰ To bind a group to a barrier, call OpenGL ExtensionsConﬁguring Swap Barriers This call binds a swap group to a barrier WglJoinSwapGroupNV, glxJoinSwapGroupNVWglBindSwapBarrierNV GlxBindSwapBarrierNV WglQueryMaxSwapGroupsNV GlxQueryMaxSwapGroupsNV WglQuerySwapGroupNV GlxQuerySwapGroupNVWglQueryFrameCountNV,glxQueryFrameCount WglResetFrameCountNV,glxResetFrameCountGetting Driver Updates Nvidia Quadro G-Sync II User Guide Registering Your Quadro Sync Registration, Support WarrantyWarranty and Support Compliance and Certiﬁcations Copyright