Nvidia 2 manual Sync and Connection Status for the Server

Page 45

NVIDIA Quadro G-Sync II User Guide

Sync and Connection Status for the Server

Sync Status

¾Receiving - Green indicates that a sync pulse is present.

¾Timing - Indicates whether the timing is locked to the sync signal Grey: The timing is locked to the internal V-Sync.

¾Stereo - Always green indicates that it is in sync with a timing signal.

Port Status

¾Out/Out is the normal indicator for the server device.

¾In/In indicates that the system is not selected as a server or client and is not frame-lock enabled.

Sync and Connection Status for the Client

Sync Status

¾Receiving - Green indicates that a sync pulse is present.

¾Timing - Indicates whether the timing is locked to the sync signal Green: The timing is locked to the signal on the frame lock conector.

Red: Either no signal on the frame lock connector is detected, or the lock to the signal has been lost

¾Stereo - Steady green indicates that the client’s stereo timing is locked to the server’s stereo signal.

Port Status

¾Out/Out is the normal indicator for the server device.

¾In/In indicates that the system is not selected as a server or client and is not frame-lock enabled.

Swap Sync

The application controls synchronization of buffer swaps (swap sync) between applications. Proper connection and synchronization of the timing signal are required for proper synchronization of buffer swaps.

38

Image 45

Contents 176-0002-000 Page Page Nvidia Quadro G-Sync Page Table of Contents References and Resources About This Guide Introduction to Nvidia Quadro G-SyncNvidia Quadro G-Sync II User Guide Implementing SLI Technology System RequirementsUnpacking Nvidia Frame SynchronizationTwo 2 Ribbon Cables Nvidia Quadro G-Sync II EquipmentSafety Instructions Installing Nvidia Quadro G-Sync II Card Quadro G-Sync Nvidia Frame Synchronization Under Windows XP Set Up the Hardware How To Set Up GenlockVID IA Q uadro G-Sync Onnector Bracket Sync Source Server Basic Genlock Setup Set Up the SoftwareClick OK to save the settings Detecting the House Sync SignalUnder The synchronization pulses are based on, click Using the House Sync SignalOu tgo in g Sync trigg ered from lead in g and falling ed ge How To Set Up Frame Lock Restoring an Unstable DisplayViewing the Connection Status Er ver Set Up the Server Software Basic Server SetupClick Apply Click Edit Settings to open the Server Settings dialog box Changing the Timing Signal FrequencyBasic Client Setup Set Up the Client SoftwareYn c D elay Skew Introducing a Timing Delay at Client SystemsSwap Sync Setup Setting Up Genlock + Frame Lock Checking the Connection Status Swap Sync Nvidia Quadro G-Sync II User Guide Nvidia Frame Synchronization Under Linux Using the nvidia-settings Utility Nvidia Q uadro G-Sync Connector Bracket Syn c Sou rce An X Server is typically speciﬁed in the format systemm Go to the nvidia-settingsframe lock panelSynchronizing to the External House Signal Ou tgo in g Sync trigg ered from lead in g and falling ed ge Understanding the Status Indicators Sync and Connection Status for the Genlock Server Four frame locked systems An X Server is typically speciﬁed in the format systemm Test the Connections Sync and Connection Status for the Server Check the Use House Sync if Present check box Frame Lock Restrictions Leveraging Frame Lock Genlock in OpenGL‰ Frame Lock + SLI SFR, AFR, or Sliaa Two Quadros, Single Supported Frame Lock ConﬁgurationsSample Conﬁgurations General StepsQuery the enabled displays on the Quadro Make sure frame lock sync is disabledGenlock Example Check that the refresh rate is the one we wantConﬁgure the house sync signal video mode Enable use of the house sync signalEnable framelocking Toggle the test signalDisable frame lock Frame Lock Example‰ First display from system Disable the house sync signal on the master device Query the enabled displays on the QuadrosEnable frame lock on server Check the refresh rate is the same for all displaysMake sure frame lock is disabled for all Quadros Enable frame lock on slave devicesVerify that the refresh rate is the same for all displays Enable frame lock on the slave devices Writing a Frame Lock NV-CONTROL ClientWriting a Frame Lock Client for NV-CONTROL 1.8 and earlier Are using a house sync. Most likely, you want Framelocksyncdisable on each X screen to disable frame lockNode Most likely, you want Writing a Frame Lock Client for NV-CONTROL 1.9 and later Conﬁguring the Frame Lock Group Querying the Frame Lock Capabilities of a SystemQuery the number of Quadro G-Sync II devices on Quadro G-Sync II device Most likely, you wantUsing a house sync. Most likely, you want Enable frame lock on each Quadro by setting NvctrlframelockEnabling/Disabling Frame Lock Nvidia Quadro G-Sync II User Guide Using the OpenGL Extensions Frame Synchronization Using the OpenGL Extensions About Buffer SwapsKey Points and Deﬁnitions Window Buffer Swaps Buffer Swap CriteriaConﬁguring for Swap Sync Frame CounterConﬁguring Swap Groups OpenGL Extensions Conﬁguring Swap Barriers‰ To bind a group to a barrier, call WglJoinSwapGroupNV, glxJoinSwapGroupNV WglBindSwapBarrierNV GlxBindSwapBarrierNVThis call binds a swap group to a barrier WglQueryMaxSwapGroupsNV GlxQueryMaxSwapGroupsNV WglQuerySwapGroupNV GlxQuerySwapGroupNVWglQueryFrameCountNV,glxQueryFrameCount WglResetFrameCountNV,glxResetFrameCountGetting Driver Updates Nvidia Quadro G-Sync II User Guide Registering Your Quadro Sync Registration, Support WarrantyWarranty and Support Compliance and Certiﬁcations Copyright