JAMO SS9000 installation manual Method

Page 25

NOTE: When completing an installation using either of the following key in sensor circuits, if the operator inserts the ignition key while the vehicle is running under the control of the Remote Start, the vehicle will shut down. This must be explained to the operator as it is in contrast to the normal opera- tion of a vehicle utilizing an electrical neutral start switch and is inconsistent with the operators manual. Additional information concerning Key In Sensor methods 1 & 2 are listed below and should be reviewed before considering either alternative.

Method 1 will allow the safety required for the remote start unit and prevent the vehicle from starting while in any gear other than Park or Neutral while the key is in the ignition cylinder however, if the key is left in the ignition switch and the door is left opened, the added relay will be energized causing a 150mA drain on the battery.

Method 2 will allow the safety required for the remote start unit and prevent the vehicle from starting while in any gear other than Park or Neutral while the key is in the ignition cylinder however, the original factory key in chime module will not alert the owner that the key has been left in the ignition switch. In addition, this may also effect other warning tones such as the light on reminder.

These situations should be carefully considered before altering the vehicle's wiring and must be fully explained to the consumer.

METHOD 1

To connect to the key in sensor as shown in method 1:

A. Locate the control wire that connects the drivers door pin switch to the key in sensor switch. B. Cut this wire and connect the ignition cylinder side to chassis ground.

C. Locate the key in sensor switch wire that connects the chime module to the ignition cylinder .

D. Cut this wire and connect the ignition cylinder side to terminal 30 of a P&B VF45F11 or equivalent relay. E. Connect the cathode (striped) side of a 4002 series diode to this same wire, and connect the (non striped) side to the negative shut down safety wire (Gray / Black) of the Audiovox Remote Start Unit.

F.Connect terminal 86 of the relay to a fused +12 volt constant battery source.

G.Connect terminal 87 of the relay to the Chime Module side of the previously cut wire in step D.

H.Connect terminal 85 of the relay to the Drivers Door side of the pin switch wire previously cut in step B. NOTE: A second 4002 series diode may be required to maintain the integrity of the hood open, shut down circuit. If this is the case, it must be installed as shown in the diagram above. The anode (Non Striped) side must be connected to the Gray/Black wire of the Remote Start Unit. The cathode (Striped) side must be connected to the hood pin switch. If the hood pin switch is also used for an alarm trigger input, be certain to use the dual diode set up shown earlier in this manual.

25

128-8843

25 of 28

Page 24 Page 26
Image 25
Page 24 Page 26
Contents Selectable Features Installation Manual128-8843 128-8843 3 128-8843 Hood PIN Switch Signal Input, Automatic Transmission and Fuel InjectionControl Module SirenShock Sensor PUSH-BUTTON/LED/RECEIVER/ANTENNAASSEMBLYStarter Inhibit Relay Fused RED w/ White Trace Wire + 12 volt Battery 1 Source Wiring the 6 PIN Main Power HarnessP O R T a N T Yellow Start Wire Detail ORANGE/BLACK Wire Parking Brake Input Wiring the 4 PIN Alternate Ignition HarnessRED/BLACK Wire + 12 Volts Input Parking Light Wiring Detail Wiring Connections Multi Pin Accessory Input/Output HarnessWhite w/ Black Trace Wire + Siren Output Positive Door Switch Wiring Detail Siren Wiring DetailHood Pin Switch Detail Shock Sensor By Pass General Motors Vats By-Pass DiagramAdditional Ignition Output GM Vats Key OverrideEntry Illumination Detail Grey w/ Black Trace Negative Inhibit Safety Shut Down DetailBrake Switch Positive Shutdown Detail Starter Inhibit Wiring DetailChassis Ground Connection Detail Negative Door Switch Wiring Detail Tachometer Input Wiring DetailGreen w/ Orange Trace Wire Tachometer Input Signal Dark Blue/Black Trace Wire External Trigger Input Channel 3 Relay Wiring DetailBlack w/ White Trace Wire 300 mA Horn Output Optional Relay RequiredWiring the 4 PIN Auxiliary Output Harness Wire Antenna/Receiver PB/LED Connector Pin Transponder Control Output Yellow ConnectorPin Shock Sensor White Connector Pin Door Lock/Unlock Harness White ConnectorWire Positive Switched Door Lock/Unlock Wiring Detail WireGround Switched Door Lock/Unlock Wiring DetailWire Ground Switched Door Lock Circuits Wire Positive Switched Door LocksWire Positive Switched 2 Step Door Locks Timed Start Operation Timed Start ProgramDiagnostics Temperature StartMulti Coil Pack Adaptor Optional Programming Tach RateTesting Your Installation Hood PIN Safety Shut Down Mechanical Neutral Safety Switch Considerations Method PIN in Vehicle Data BUS Port DBI Port Completing the Installation 128-8843

SS9000 specifications

The JAMO SS9000 is an innovative sound system that has gained attention for its impressive combination of performance, design, and usability. As part of the JAMO range, this model stands out for its ability to deliver exceptional audio quality while offering advanced features that cater to the modern listener.

One of the main features of the JAMO SS9000 is its state-of-the-art speaker technology. It employs advanced driver designs that ensure clear and precise sound reproduction across a wide frequency range. The system utilizes a combination of woofer and tweeter components to provide a balanced sound profile, making it suitable for various music genres and listening preferences. With its robust construction and high-quality materials, the JAMO SS9000 is built to last while delivering consistent performance.

Another key characteristic of the JAMO SS9000 is its wireless capabilities. The system supports Bluetooth connectivity, allowing users to stream music directly from their smartphones or tablets quickly. This feature enhances user convenience, eliminating the need for cumbersome wires and creating a tidy, uncluttered listening environment. Additionally, the JAMO SS9000 is compatible with various streaming services and devices, making it a versatile addition to any home audio setup.

The design of the JAMO SS9000 is both stylish and functional. Its sleek lines and modern aesthetics make it an attractive piece for any room, blending seamlessly with contemporary decor. Available in different finishes, users can select a color that complements their style and preferences.

Furthermore, the JAMO SS9000 incorporates advanced acoustic technologies that enhance its performance. The system features a sophisticated anti-distortion mechanism that ensures clean sound even at higher volumes. This technology is critical for audiophiles who demand clarity and fidelity in their music.

Overall, the JAMO SS9000 stands out for its combination of impressive audio performance, modern design, and practical features. Whether used for casual listening or more critical listening sessions, this system promises to deliver an exceptional audio experience that caters to the needs of today's consumers. With its robust build quality, wireless capabilities, and aesthetic appeal, the JAMO SS9000 is a worthy consideration for anyone looking to upgrade their home audio setup.
Top Page Image Contents