Action | System Response | No response |
| Turn ignition on | |
| Press and release the valet switch 3 times | 1 Chirp - LED 1 flash |
| Within 3 seconds, turn ignition Off, On, Off, On | Short chirp, then 2 long chirps |
| This Action Accesses Feature Bank 3 Remote Start Selectable Features | |
First | Press the valet switch one time | 1 chirp = defrost output pulsed |
| Press transmitter Lock button to change | 2 chirps = defrost output 10 Mins |
Second | or | 2 chirps = RF start chirp on |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 1 chirp = RF start chirp off |
Third | or | 2 chirps = run time set for 10 mins |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 3 chirps = run time set fro 15 mins |
| Press transmitter Lock button to change | 4 chirps = run time set for 20 mins |
| Press transmitter Lock button to change | 5 chirps = run time set for 45 mins |
| Press transmitter lock button to change | 6 chirps = run time set for 60 mins |
| Press transmitter lock button to change | 1 chirp = run time set for 5 mins |
Fourth | or | 1 chirp = parking lights on steady w/RS active |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 2 chirps = parking lights flashing w/RS active |
Fifth | or | 2 chirps = tachometer input checking |
Press and release the valet switch | ||
| Press transmitter Lock nutton to change | 3 chirps = DBI Tach Mode |
| Press transmitter Lock button to change | 4 chirps = Hybrid Mode |
| Press transmitter Lock button to change | 1 chirp = voltage sense input checking |
Sixth | or | 1 chirp = greater than 0.5 V check before start |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 2 chirps = less than 0.5 V check before start |
Seventh | or | 2 chirps = ign 2 on during crank |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 3 chirps = ign 2 same as accessory |
| Press transmitter Lock button to change | 1 chirp = ign 2 off during crank |
Eighth | or | 2 chirps = ign 3 on during crank |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 3 chirps = ign 3 same as accessory |
| Press transmitter Lock button to change | 4 chirps = ign 3 same as starter |
| Press transmitter Lock button to change | 1 chirp = ign 3 off during crank |
Ninth | or | 1 chirp = diagnostics off |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 2 chirps = diagnostics on |
Tenth | or | 2 chirps = crank time 1.0 sec |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 3 chirps = crank time 1.5 sec |
| Press transmitter Lock button to change | 4 chirps = crank time 2.0 sec |
| Press transmitter Lock button to change | 1 chirp = crank time 0.8 sec |
Eleventh | or | 1 chirp = unit set for gasoline engine |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 2 chirps = unit set for diesel engine 10 sec delay |
| Press transmitter Lock button to change | 3 chirps = unit set for diesel engine 15 sec delay |
| Press transmitter Lock button to change | 4 chirps = unit set for diesel engine 20 sec delay |
Twelfth | or | 1 chirp = transponder output while R/S active |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 2 chirps = transponder output during start only |
| Press transmitter Lock button to change | 3 chirps = transponder output until ignition turned off |
Thirteenth | or | 1 chirp = temperature start off |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 2 chirps = temperature start on |
Fourteenth | or | 1 chirp = crank averaging w/voltage input checking |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 2 chirps = preset crank time w/voltage input check |
Fifteenth | or | 1 chirp = shk sensor shunted until clear |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 2 chirps = shk sensor shunted for the R/S Cycle |
| Press transmitter Lock button to change | 3 chirps = shk sensor shunted from tx 1 start cycle |
Sixteenth | or | 1 chirp = turbo timer off |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 2 chirps = turbo timer 3 mins |
| Press transmitter Lock button to change | 3 chirps = turbo timer 5 mins |
| Press transmitter Lock button to change | 4 chirps = turbo timer 10 mins |
Seventeenth | or | 1 chirp = aux o/p Black/Blue single pulse |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 2 chirps = aux o/p Black/Blue as alarm feature #1 |
Eighteenth | or | 1 chirp = double press to start |
Press and release the valet switch | ||
| Press transmitter Lock button to change | 2 chirps = single press to start |
| or | Exit Programming Mode |
| Turn the ignition off to: |
NOTE: Once you enter the feature programming mode, do not allow more than 15 seconds to pass between steps or the programming will be terminated.
4
128-8843
4 of 28