Kingston Technology KND810TX, KND2410TX, KND1610TX manual Hardware Installation, Front Panel

Page 10

4

Front Panel

Hardware Installation

Before you begin installing network cables, please take a few minutes to familiarize yourself with the dual-speed hub. See the diagram below:

Front Panel

100TX LEDs

Link / Activity LEDs

 

 

1

2

3

4

5

6

7

8

9

10

11

12

 

 

13

14

15

16

17

18

19

20

21

22

23

24

24

Power LED

Collision LEDs

 

 

10/100BASE - TX

 

 

 

 

Uplink Port

 

for 10 and 100

 

 

 

UTP Ports

 

 

 

 

 

 

 

Fig. 1-2 KND2410TX Front Panel

 

 

Power LED

The green LED indicates the power status. The LED will light up when the AC power connector is properly connected to a power source.

Collision LEDs

There are two (2) separate collision LEDs for both 10Mbps and 100Mbps segments. If a collision is detected on a 10Mbps segment, the “10” LED will flash amber. If a collision is detected on a 100Mbps segment, the “100” LED will flash amber. Collisions occur when 2 or more ports receive data simultaneously

100TX (Speed-Detection) LEDs

The 100TX LED lights up when 100Mbps operation is detected. The 100TX LED will not light up if 10Mbps operation is detected.

Link / Activity LEDs

The LINK / ACTIVITY LEDs service both 10BASE-T and 100BASE-TX operation. A steady green light indicates that a good link has been established. A flashing green light indicates that data is being received.

If the Link LED does not display a steady green link light, please check the following:

Kingston Technology Company

KND2410TX User’s Guide - Rev. A01

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Models KND810TX KND1610TX KND2410TX Page 10/100TX Rack-Mountable Dual Speed Hubs User’s Guide Important Safety InstructionsPart No -001.A01 Table Of Contents Power Switch AC Power Connector Kingston Technology Company KND2410TX User’s Guide Rev. A01 Introduction Model TypesSpecial Features Package ContentsDesign Features Hardware Installation Front Panel10/100TX UTP Ports Uplink PortRear Panel Power SwitchAC Power Connector FuseStacking Configuration Stack-In / Stack-Out PortsSpeed-Setting Dip Switches Port no orAppendices Appendix a Pin Assignments UTP Port Pin AssignmentsAppendix B Cabling Guidelines UTP Cable WiringUTP Cable Wiring Standards UTP Cable TypeUTP Cable Rating Codes T568A Pairs Strand SolidAppendix C Specifications Terms You Should Be Familiar WithAppendix C Specifications Appendix D Commonly Asked Questions Class I vs. Class II 100BASE-TX Fast Ethernet RepeatersAppendix E Warranties and Notices Category 5 Compliance vs. Category 5 Performance?Limited Warranty Statement Duration of WarrantyFree Technical Support Warranty Claim RequirementsDisclaimers CE Notice C. CertificationTick Certification

KND2410TX, KND1610TX, KND810TX specifications

Kingston Technology's KND810TX, KND1610TX, and KND2410TX represent a significant leap in the memory module landscape, delivering high performance and reliability tailored for both consumer and enterprise applications. These models are part of Kingston's expansive range of DRAM solutions, ensuring that users get optimal speed and performance whether for gaming, content creation, or data-intensive enterprise tasks.

Starting with the KND810TX, this model highlights an impressive balance of performance and power efficiency. Designed for high-speed computing, it operates at DDR4 speeds, which allows for faster data transfer rates compared to its predecessors. Its low latency characteristic ensures that applications run smoothly and efficiently, making it ideal for gamers who require quick data access to enhance their gameplay experience. Furthermore, the KND810TX supports Intel's XMP (Extreme Memory Profile) technology, which allows users to optimize the memory settings through BIOS for maximum performance.

Next in line is the KND1610TX, a memory module that shines brightly in multi-tasking environments. This variant offers increased capacity options, accommodating more applications running simultaneously without compromising speed. Its robust design features advanced thermal management that allows it to operate under heavy workloads without overheating. The KND1610TX is particularly favorable for creators working with high-resolution video editing and graphic design, where memory demands can soar.

Lastly, the KND2410TX stands out with its high-capacity offerings, making it suitable for server environments and data centers. Built for mission-critical applications, this module demonstrates exceptional reliability and durability. The KND2410TX utilizes error-correcting code (ECC) technology, which automatically detects and corrects memory errors, ensuring data integrity during intensive tasks. This feature is particularly important for enterprise users who depend on absolute precision and reliability in their memory systems.

All three models—KND810TX, KND1610TX, and KND2410TX—incorporate cutting-edge technologies ensuring compatibility with various platforms while adhering to rigorous industry standards. Kingston's commitment to quality is evident through extensive testing and certifications, allowing customers to depend on these memory solutions for both personal and professional use. In sum, these memory modules from Kingston Technology provide a perfect blend of speed, reliability, and capacity, catering to the diverse needs of today's tech-driven users. Whether for casual use or professional environments, Kingston continues to set the benchmark for high-performance memory solutions.
Top Page Image Contents