Kingston Technology KND2410TX, KND810TX manual Rear Panel, Power Switch, AC Power Connector, Fuse

Page 12

6Rear Panel

Rear Panel

AC Power

Power Switch

Connector

 

U S E O N L Y W I T H A 2 5 0 V F U S E

Dip Switches

Stack-In / Stack-Out

Fan

Fuse (250V, 2A)

 

Ports

 

 

 

 

Fig. 1-3 Rear Panel

Power Switch

The AC Power switch turns the unit ON or OFF. If the PWR LED does not light up once the unit has been turned on, try the procedures below (in the following order):

1.Try a different AC power outlet.

2.Check the external fuse located at the back of unit (below the AC power connector). If the fuse is blown, replace it with the spare fuse provided with the unit. (See Fuse Compartment display on page 8)

3.The power supply may be defective. Return the unit for replacement.

WARNING: For safety reasons, DO NOT attempt to open and service the unit. There are no user-serviceable components inside.

AC Power Connector

The Fast EtheRx dual-speed hubs use 100-240VAC internal power supplies. Connect the AC power cord from the back of the unit to an AC electrical outlet.

Fuse

The Fast EtheRx dual-speed hubs come equipped with one external fuse and one spare fuse. Both fuses are in a fuse holder located just below the AC power connector on the back of the unit. Both fuses are rated 250V/2A max.

Fan Unit(s)

The Fast EtheRx dual-speed hubs use independent cooling fans for optimum air- flow to safeguard the unit from unnecessary heat exposure.

Kingston Technology Company

KND2410TX User’s Guide - Rev. A01

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Models KND810TX KND1610TX KND2410TX Page Important Safety Instructions 10/100TX Rack-Mountable Dual Speed Hubs User’s GuidePart No -001.A01 Table Of Contents Power Switch AC Power Connector Kingston Technology Company KND2410TX User’s Guide Rev. A01 Introduction Model TypesSpecial Features Package ContentsDesign Features Hardware Installation Front Panel10/100TX UTP Ports Uplink PortPower Switch AC Power ConnectorRear Panel FuseStacking Configuration Stack-In / Stack-Out PortsSpeed-Setting Dip Switches Port no orAppendices Appendix a Pin Assignments UTP Port Pin AssignmentsUTP Cable Wiring UTP Cable Wiring StandardsAppendix B Cabling Guidelines UTP Cable TypeUTP Cable Rating Codes T568A Pairs Strand SolidAppendix C Specifications Terms You Should Be Familiar WithAppendix C Specifications Appendix D Commonly Asked Questions Class I vs. Class II 100BASE-TX Fast Ethernet RepeatersAppendix E Warranties and Notices Category 5 Compliance vs. Category 5 Performance?Limited Warranty Statement Duration of WarrantyWarranty Claim Requirements Free Technical SupportDisclaimers C. Certification CE NoticeTick Certification

KND2410TX, KND1610TX, KND810TX specifications

Kingston Technology's KND810TX, KND1610TX, and KND2410TX represent a significant leap in the memory module landscape, delivering high performance and reliability tailored for both consumer and enterprise applications. These models are part of Kingston's expansive range of DRAM solutions, ensuring that users get optimal speed and performance whether for gaming, content creation, or data-intensive enterprise tasks.

Starting with the KND810TX, this model highlights an impressive balance of performance and power efficiency. Designed for high-speed computing, it operates at DDR4 speeds, which allows for faster data transfer rates compared to its predecessors. Its low latency characteristic ensures that applications run smoothly and efficiently, making it ideal for gamers who require quick data access to enhance their gameplay experience. Furthermore, the KND810TX supports Intel's XMP (Extreme Memory Profile) technology, which allows users to optimize the memory settings through BIOS for maximum performance.

Next in line is the KND1610TX, a memory module that shines brightly in multi-tasking environments. This variant offers increased capacity options, accommodating more applications running simultaneously without compromising speed. Its robust design features advanced thermal management that allows it to operate under heavy workloads without overheating. The KND1610TX is particularly favorable for creators working with high-resolution video editing and graphic design, where memory demands can soar.

Lastly, the KND2410TX stands out with its high-capacity offerings, making it suitable for server environments and data centers. Built for mission-critical applications, this module demonstrates exceptional reliability and durability. The KND2410TX utilizes error-correcting code (ECC) technology, which automatically detects and corrects memory errors, ensuring data integrity during intensive tasks. This feature is particularly important for enterprise users who depend on absolute precision and reliability in their memory systems.

All three models—KND810TX, KND1610TX, and KND2410TX—incorporate cutting-edge technologies ensuring compatibility with various platforms while adhering to rigorous industry standards. Kingston's commitment to quality is evident through extensive testing and certifications, allowing customers to depend on these memory solutions for both personal and professional use. In sum, these memory modules from Kingston Technology provide a perfect blend of speed, reliability, and capacity, catering to the diverse needs of today's tech-driven users. Whether for casual use or professional environments, Kingston continues to set the benchmark for high-performance memory solutions.
Top Page Image Contents