GarrettCom 84-00136 manual Www . GarrettCom . com

Page 50

Magnum 6K16-Series Managed Fiber Switch Installation and User Guide (04/06)

6K16-Series Switch’s RJ-45 ports handle this situation by configuring the ports as per desire through MNS software port settings and can check the port status of each port after the change.

When Magnum 6K16-Series RJ-45 copper ports are set for auto-negotiation and are connected to another auto-negotiating device, there are 4 different speed and F/H modes possible depending on what the other device supports. These are: (1) 100Mb full- duplex, (2) 100Mb half-duplex, (3) 10 Mb full-duplex and (4) 10 Mb half-duplex.

The auto-negotiation logic will attempt to operate in descending order and will normally arrive at the highest order mode that both devices can support at that time. (Since auto- negotiation is potentially an externally controlled process, the original “highest order mode” result can change at any time depending on network changes that may occur). If the device at the other end is not an auto-negotiating device, the 6K16-Series’s RJ-45 ports will try to detect its idle signal to determine 10 or 100 speed, and will default to half-duplex at that speed per the IEEE standard.

General information -

Auto-negotiation per-port for 802.3u-compliant switches occurs when:

--the devices at both ends of the cable are capable of operation at either 10 Mb or 100Mb speed and/or in full- or half-duplex mode, and can send/receive auto-negotiation pulses, and . . .

--the second of the two connected devices is powered up*, i.e., when LINK is established for a port, or

--the LINK is re-established on a port after being lost temporarily.

•NOTE – Some NIC cards only auto-negotiate when the computer system that they are in is powered up. These are exceptions to the “negotiate at LINK – enabled” rule above, but may be occasionally encountered.

When operating in 100Mb half-duplex mode, cable distances and hop-counts

may be limited within that collision domain. The Path Delay Value (PDV) bit-times must account for all devices and cable lengths within that domain. For Magnum 6K16-Series Fast Ethernet switched ports operating at 100Mb half-duplex, the bit time delay is 50BT.

www . GarrettCom . com

42

Page 49 Page 51
Image 50
Page 49 Page 51
Contents Managed Fiber Switch Trademarks Contacting GarrettCom, Inc Canadian EmissionIntroduction Table of ContentsInstallation Intro Magnum 6K16/6K16V Managed Fiber Switch Port Modules45 OperationWww . GarrettCom . com Overview TRANSCEIVERS, 10MB Series MINI-TRANSCEIVERS and Coax Models Media CONVERTERS, 10MB and 100MB SeriesBridge Port Modules BPMS, 4 TYPES, for Segment Network Standards and Compliance, hardware Technical SpecificationsPerformance Maximum 10 Mbps Ethernet Segment LengthsManagement Console connector Fiber Single-mode connector typesAlarm Relay Contacts Power Supply InternalAgency Approvals and Standard Compliance Magnum 6K16V Per-port MDI or Mdix on RJ-45Mountings Magnum 6K16Ordering Information 6KP8-SLC 6KP8-MTRJ6KP8-MLC 6KP4-FXSCWww . GarrettCom . com 6K PoE Modules with 48VDC Pass-Through Introduction Inspecting the Package and Product Product Description Magnum 6K16-Series 6K16/6K16V 1a Magnum 6K16V, Managed Fiber Switch 1b Magnum 6K16, Managed Carrier Class Switch 1c Magnum 6K16-Series family 6K16 and 6K16V, At a glance Set-up of the software See Magnum 6K-MNS Software Manual for Flexibility to adapt to any FDX orEight-Port Copper Module, 6K8-RJ45 Per the IEEE802.3af PoE Port modules are also available with Four-Port 10 Mb and 100Mb mm Fiber ST ModulesMagnum Combo six @ Mtrj 100Mb mm SFF fiberGigabit 1000Mbps port modules Packet Prioritization, 802.1p QOSFrame Buffering and Flow Control Managed Network Software MNS-6K for Magnum 6K8-Series GarrettCom proprietary MIBs for Snmp„ Features Fiber-Built-In Features and Benefits„ Managed switching for high performance Ethernet LANs Applications Magnum 6K25 Snmp Backup Locating Magnum 6K16-Series Switches Connecting Ethernet MediaConnecting Single-Mode Fiber Optic Connecting Fiber Optic ST-type, twist-lockConnecting Fiber Optic SC-type, Snap-In Ieee Standard Media Type Max. Distance Port Module FiberMedia Ieee Standard Connecting Gigabit Media Using GBICs DIN-Rail Mounting Magnum 6K16VWww . GarrettCom . com Mounting Dimensions for 6K16Vwith metal brackets 2a- One Magnum 6K16 deployed over a K16-2Tray Powering the Magnum 6K16-Series Managed Fiber Switch Relay Contacts6K16-Series Port Module 6KPM Installation Preparation for Installing and Removing 6KPMsRemove Chassis Cover 1a Removing the Front panel from the unitInstalling 6KPM Cards in the Magnum 6K16-Series Remove front panel face plate retaining screwsUplink Switch 2f Securely latching up 6KPM Cards into a Magnum 6K16-Series Removing 6KPM Cards 3b Removing a 6KPM CardEnlarged view of Magnum 6K16-Series Console Port area DB-9 Console port connector1 RS-232 DB-9 Console Com port Serial port pin assignments Address Learning Switching FunctionalityFiltering and Forwarding Auto-CrossMDIX and Auto-negotiation, for RJ-45 ports Up-link Manual Switches set as = , for RJ-45 port onlyStatus LEDs PWRWww . GarrettCom . com Flow-control, Ieee 802.3x standard 6KP4V ’cvr6KPM Module Description Dual speed copper ports. Segments. When installed in aSwitch, the copper port Magnum 6K16-Series Managed1b 6KP4-F10ST, 4@10Mb multi-mode FX-ST twist lock Module Transceivers all in one module. This Mode 100Mbps fiber opticMagnum 6KP6 Activity ACT, Link LK,Www . GarrettCom . com Link Port@ 100Mbps Multi-Mode Fiber portActivity FULL/HALF Module is a combo module with Mtrj type ports. The small size Mtrj connectors provides anMagnum 6KP8-45MT Copper and fiber Small Form Factor9 6KP8-RJ45 Twisted Pair, 10/100Mb 8-Port Fig. the top 8-RJ45 PoE LEDs SummaryMagnum 6KP8 GBIC-SXSC Gigabit fiber1000Mb, multi-mode SC Connector 13a GBIC-LXSC Gigabit fiber 1000Mb, multi-mode SC Connector14 6KM-BLNK @ 1000Mb Fiber SC + 2@ 100Mb SCBefore Calling for Assistance When Calling for Assistance Return Material Authorization RMA ProcedureShipping and Packaging Information Appendix B Internal DC Power Supply OptionsNo Problem Found B2.0 -48VDC, 24VDC and 125VDC POWER, Theory of Operation B3.0 Applications for DC Powered Ethernet Switches B4.0 6K16-SERIES, -48V, 24, 125 or 5VDC InstallationB5.0 Operation B7.0 TroubleshootingC1.0 Specifications for Magnum 6K16-SERIES Fiber Switch B6.0 Ordering InformationC4.0 Features and Benefits of the DUAL-SOURCE Design GNDC5.0 Installation Example Magnum 6K16-SeriesR-48VDC C5.1 UL RequirementsC6.0 Ordering Information C7.0 Operation

84-00136 specifications

GarrettCom 84-00136 is a robust and reliable networking solution widely recognized for its versatility and performance in demanding environments. Specifically designed for industrial applications, the device excels in offering connectivity within harsh conditions, ensuring seamless communication across various network topologies.

One of the standout features of the GarrettCom 84-00136 is its high port density. With multiple Ethernet ports, it allows for extensive network connections, making it an ideal choice for facilities that require numerous devices to be interlinked. This capability ensures that organizations can efficiently manage their communication needs without compromising on performance.

Another significant characteristic of the 84-00136 is its industrial-grade durability. Built to withstand extreme temperatures, vibrations, and shocks, the device is suited for applications in manufacturing plants, transportation systems, and utility networks. This level of resilience is essential for maintaining reliable operations in environments where standard networking equipment might fail.

The technology behind the GarrettCom 84-00136 includes advanced switching capabilities. With support for both managed and unmanaged configurations, users can choose the level of control and customization that best fits their network requirements. The managed features allow for extensive monitoring and management, facilitating better network performance and security.

In addition, the 84-00136 supports various communication protocols, improving interoperability with existing systems. This flexibility is crucial for organizations looking to integrate new technologies into their established networks without overhauling the entire system.

Security is another critical aspect of the GarrettCom 84-00136. The device is equipped with robust security features, ensuring that network data remains protected from unauthorized access. This is particularly important in industrial environments where sensitive information must be safeguarded against potential cyber threats.

Ease of installation and maintenance is also a highlight of the GarrettCom 84-00136. Its user-friendly design allows for straightforward setup, minimizing downtime during deployment. Furthermore, ongoing maintenance is simplified through an intuitive interface, enabling quick troubleshooting and adjustments.

In summary, the GarrettCom 84-00136 is a high-performance networking solution tailored for industrial applications. Its impressive features, including high port density, industrial-grade durability, advanced switching capabilities, and robust security measures, make it an optimal choice for organizations seeking reliable and efficient network connectivity in challenging environments.
Top Page Image Contents