GarrettCom 6KQ manual Ordering Information

AGENCY APPROVALS AND STANDARDS COMPLIANCE:

UL Listed (UL60950), cUL, CE, Emissions meet FCC Part 15, Class A. NEBS L3 and ETSI compliant

IEC61850 EMC and Operating Conditions Class C for Power Substations IEEE 1613 Environmental Standard for Electric Power Substations.

NEMA TS-2 & TEES for DC-powered and PoE-powered traffic ctrl equipment. Class1 Division 2 for hazardous locations = pending

NETWORK CABLE CONNECTORS:

Specifications

Industrial Ethernet Managed Field Switch

PERFORMANCE:	DC DUAL POWER SOURCE (OPTIONAL)
Fiber Ports, 100 Mb: Configurable SC, ST, LC and MTRJ, multi-mode and	All Magnum 6KQ models (24VDC, 48VDC, 125VDC) may be ordered with op-
single-mode for each type, max of 12 fiber	tional Dual-Source DC power input, for continuity of operation when either one
Fiber Ports, 10 Mb: Configurable, ST, up to 4 fiber mm ports, each FDX or
	of the DC input sources is interrupted.
HDX, default is HDX mode.
RJ-45 Ports: 100 or 10 Mb speed, full- or half-duplex mode, per port, individ.	MECHANICAL:
determined. 10/100 auto-negotiating & auto-cross, up to 12 ports.	Enclosure: High-strength extruded aluminum for heat-sinking. Vertical panel-
PoE Ports, RJ-45 Power Sourcing per IEEE 802.3af, power on data pair,
	mounting brackets included.
configurable up to 8 PoE ports.
	DIN-Rail mounting: Model # DIN-Rail-6KQ, optional
Gigabit Ports, 1000 Mb: Configurable, standard SFP transceiver modules or
	Enclosure Ingress Protection rating: IP53, protects against (5)dust particles
10/100/1000Mb copper, up to 2 Gigabit ports.
	and (3)spraying liquids per IEC 60529, and NEMA-3,3X
Processing type: Store and Forward with IEEE 802.3p QOS and IEEE 802.3x
	Cooling Method: Convection, fully-enclosed ribbed-surface aluminum case
full-duplex flow control.	used as a heat sink, designed for vertical mounting, no fans.
All Ports non-blocking. System aggregate forward and filter rate 4.76M pps.
	Dimensions: 6.85 in H x 7.50 in W x 2.0 in D in vertical panel-mount position.
Address table: 4K nodes, with address aging time of 300 seconds typical.
	(17.4cm H x 19.1cm W x 5.08cm D) Weight: 3 lbs. (1.3 kg)
Packet buffers: 240 KB for 10/100 and 120KB for 1000 Mb
Latency: 6μs + packet time max (TX - TX, TX - FX, FX - FX, TX-G, G-G)	LED INDICATORS (two sets) PER RJ-45 PORT:
NETWORK STANDARDS:	LK: Steady ON when twisted-pair link is operational.
	ACT: ON with port activity
IEEE 802.3, 802.3ab, 802.1p:10BASE-FL;100BASE-TX,FX;1000BASE-SX,LX,ZX 100/10 ON = 100Mb speed, OFF = 10Mb
Auto-negotiation and auto-cross on 10/100 TP and PoE, IEEE 802.3u	(Port-side LED set only) F/H: ON for full-duplex, OFF for half-duplex

See MNS-6K datasheet for software network standards and software features. (PoE only, port-side only) PoE: ON for power to PD device. Note: LK/ACT port

All 10 Mb ports obey the rules for configuring 10 Mb Ethernet	becomes steady ON for Link, blinking for activity.
All 100 Mb ports use Fast Ethernet rules. 1000 Mb ports use Gigabit rules.
OPERATING ENVIRONMENT:	LED INDICATORS (two sets) per 100Mb and 10Mb FIBER PORTS:
	LK: Steady ON when fiber link is operational
UL 60950 and “Component Parts” rating: -40° to 140°F (-40° to 60°C)	ACT: ON with port activity
IEC 60068 “Type Test” rating: -60° to 195°F (-50° to 85°C)	(Port-side LED set only) F/H: ON for full-duplex, OFF for half-duplex
Storage: -60° to 210°F (-50°to 100°C)
Relative humidity: 5% to 95% (non-condensing)	LED INDICATORS PER Gb PORT:
Altitude: -200 to 13,000ft (-60 to 4,000m)	LK: Steady ON when link is operational.
Conformal coating (humidity protection) optional: Request quote	ACT: ON with port activity	1000Mb ON = Gb speed
RELAY CONTACTS FOR ALARMS (OPTIONAL):	(Top-side LED set only, copper only) 100/10 ON = 100Mb speed, OFF = 10Mb
	(Port-side LED set only) F/H: ON for full-duplex, OFF for half-duplex
Form C, one NC indicating internal power, one NC software controllable.	(Port-side LED set only, copper only) 3 LEDs indicate Gb, 100Mb or 10Mb speed

PORT-SPECIFIC SETTINGS:

1000Mb fiber ports: all standard Gb SFP Transceiver types supported Port-specific user settings (such as FDX or HDX, copper 10/100 speed) can

1000Mb copper ports:10/100/1000Mb auto-negotiating, Cat5e & 6 UTP/STP be set using software commands. (The RJ-45 copper ports are auto- 100Mb Copper and PoE: Category 5 UTP/STP; 10 Mb: Cat. 3, 4, 5 UTP/STP negotiating auto-crossover, there are no user controls for auto-crossover).

100Mb Fiber ports connector options: multi-mode FX-MTRJ, LC, ST, SC; sgl-mode 15Km LC, 20Km SC and ST, and 40Km “long reach” sgl-mode SC.

10Mb Fiber port connector: multi-mode ST, 10BASE-FL

For other port types and port connector types, request quote

DC POWER SUPPLY (Internal, floating ground for internal PCBs): Power Input: 24V nominal (18 to 36V), 48V nominal (36 to 60V), 125V nominal (88 to 150V)

Power Input for PoE: 48VDC pass-through, add up to 15 watts per PoE port

Power Consumption: 35 watts typical for a fully-loaded fiber model, 20 watts typical for 4 port copper-only model.

Std. Terminal Block: “-, GND, +”. Dual Source Terminal Block is -A, -B, +A, +B, chassis ground.

WARRANTY: Three years	Made in USA
♥2006 GarrettCom, Inc. Printed in United States of America	Doc No. 6KQ-R1 10/06

GarrettCom, Inc. reserves the right to change specifications, performance characteristics and/or model offerings without notice. GarrettCom, Magnum, DYMEC, DynaStar, S-Ring, RS-Ring, and Link-Loss- Learn, are trademarks and Personal Hub is a registered trademark of GarrettCom, Inc. NEBS is a registered trademark of Telcordia Technologies. UL is a registered trademark of Underwriters Labs.

Ordering Information

Magnum 6KQ-24VDC Magnum 6KQ Managed Field Switch, base unit. May be configured with a variety of 10/100/1000 Mb fiber and copper port connector types from a family of port modules. Non-blocking filtering & forwarding across all ports. Heavy duty metal case designed as heat sink, IP53 for environmental protection,no fans.

Magnum 6KQ-48VDC Same as Model 6KQ-24VDC except the power input is -48VDC.

Magnum 6KQ-125VDC Same as Model 6KQ-24VDC except the power input is 125VDC range 88-150VDC). Magnum 6KQP-48VDC PoE, same as Model 6KQ-48VDC except the four 10/100 ports are PoE-enabled, data pairs.

Configuration Options: Each Magnum 6KQ may be configured with a choice for the three modular slots.

6KQ4-RJ45	6KQ module, four 10/100 copper ports, may be used in 6KQ slots B and/or D
6KQ4-RJMLC	6KQ module, two 10/100 copper ports and two 100Mb 2km multi-m. LC fiber ports, slots B and/or D
6KQ2-10ST	6KQ module, two 10 Mb FL 2km multi-mode ST fiber ports, slots B and/or D
6KP8-MTRJ	SFF Fiber module for 6K Switches, w/eight 100 Mb 2km multi-mode FX MTRJ connectors
6KQ2-MST	6KQ module, two 100Mb 2km multi-mode ST fiber ports, slots B and/or D
6KP6-RJMST	“4+2” module for 6Ks, w/four 10/100 RJ-45 and two 100 Mb 2km multi-mode FX ST connectors
6KQ2-SSC	6KQ module, two 100Mb 20km single-mode SC fiber ports, slots B and/or D
P6KQ4-RJ45	PoE 6KQ module, four 10/100 copper ports with PoE on data pairs, may be used in 6KQ slot B only
6KQF-4MT	6KQ module, four 100Mb 2km multi-m. MTRJ fiber ports, factory slot C fiber-only
6KQF-2MSC	6KQ module, two 100Mb 2km multi-mode SC fiber ports, factory slot C fiber-only
6KQF-1MST	6KQ module, one 100Mb 2km multi-mode ST fiber ports, factory slot C fiber-only
6KQ-2GSFP	6KQ Gig module, two SFP pluggable open transceiver ports for user-selectable
	SFP Gig transceivers in each, configure in 6KQ slot D only
6KQ-2GCU	6KQ Gig module, two auto-negotiating 10/100/1000 Mb copper ports, configure in 6KQ slot D only

Several other Port Modules are available on config. guide at www.garrettcom.com/techsupport/insertion_guides/6kqcg.pdf

DIN-RAIL-6KQ	DIN-Rail holder for a secure vertical mount of 6KQ, with screws to attach to 6KQ case.
CONFORMAL CRM	Conformal coating (aka "tropical treatment") of interior PCBs and each module of one 6KQ or 6K8 Switch

DEWAR ELECTRONICS Pty. Ltd.

32-34 Taylors Road

Croydon, Vic. 3136

PH: (03) 9725 3333

FAX: (03) 9725 6003 Email: sales@dewar.com.au Web: www.dewar.com.au