Fortinet 50A/50B, 100 manual Index, Cli

Page 81

Index

Index

A

adding a default route 38, 41

C

CAT5 20

certificate, security 22

CLI

additional CLI commands, FortiUSB 75 connecting 23

upgrading the firmware 66, 68 comments, documentation 13 configuring

redundant mode 52 standalone mode 52

connecting

to the CLI 23

to the web-based manager 21 customer service 13

D

dead gateway detection 55 default

adding a route 38, 41 restoring settings 31

DHCP configuration 37

documentation commenting on 13 Fortinet 12

E

Ethernet, Power 20

F

factory defaults

DHCP server configuration 28 firewall configuration 29 NAT/Route mode config 28 protection profiles 30 Transparent mode config 29

firewall policies modem 56

firmware

backup and restore from FortiUSB key 73 install, backup firmware image 77 installing 70

re-installing current version 70 restoring previous config 72 reverting to an older version 70 testing new firmware 75 upgrading to a new version 65 upgrading using the CLI 66, 68

upgrading using the web-base manager 31, 65, 67 FortiGate documentation

commenting on 13

Fortinet 9

Fortinet customer service 13 Fortinet documentation 12 Fortinet Family Products 9

FortiBridge 10

FortiClient 9

FortiGuard 9

FortiLog 10

FortiMail 9 FortiManager 10 FortiReporter 10

Fortinet Knowledge Center 13 FortiUSB key

additional CLI commands 75 backup and restore 73 USB Auto-Install 74

G

grounding 20

I

IEEE 802.3af 20

installing factory defaults 24 introduction

Fortinet documentation 12

L

LED descriptions 19

M

modem

adding firewall policies 56 redundant mode 51 standalone mode 51, 52

modem CLI commands altmode 53 auto-dial 53 connect_timeout 53 dial-on-demand 53 holddown-timer 53 idle-timer 53 interface 53 mode 53 passwd1 53 passwd2 54 passwd3 54 peer_modem1 54 peer_modem2 54 phone1 54 phone2 54 phone3 54

redial 54 status 54 username1 54 username2 54 username3 54

FortiGate-50A/50B, FortiWiFi-50B and FortiGate-100 FortiOS 3.0 MR4 Install Guide

01-30004-0265-20070831

81

Image 81

Contents Install G U I D E Regulatory compliance TrademarksContents Configuring the FortiGate unit Factory defaultsConfiguring the modem interface Using a wireless networkFortiGate Firmware Index Reverting to a previous firmware versionFortiUSB key Introduction About the FortiGate unitFortiGate-50A FortiGate-50B FortiWiFi-50BFortiGate-100 Register your FortiGate unitFortinet Family Products FortiGuard Subscription ServicesFortiClient FortiMailFortiAnalyzer About this documentFortiReporter FortiBridgeTypographic conventions Document conventionsFortinet documentation Fortinet Tools and Documentation CD Customer service and technical supportFortinet Knowledge Center Comments on Fortinet technical documentationCustomer service and technical support Package Contents Installing the FortiGate unitWeight Technical Specifications DimensionsPower Requirements SpecificationsFortiWiFi-50B package contents Back FortiGate-100 package contents FrontPowering on the FortiGate unit To power on the FortiGate unitMounting Power over Ethernet Connecting to the FortiGate unit Powering off the FortiGate unitCommand line interface Connecting to the web-based managerTo connect to the web-based manager FortiGate loginTo connect to the CLI Connecting to the CLIBits per second 9600 Data bits Parity Stop bits Flow controlQuick configuration using default settings Quick installation using factory defaultsGo to System Network Options Quick installation using factory defaults Factory defaults Factory default NAT/Route mode network configuration Factory default Dhcp server configurationFactory default firewall configuration Factory default Transparent mode network configurationAdministrative access Management IPFactory default protection profiles Restoring the default settings using the web-based manager Restoring the default settingsRestoring the default settings using the CLI To reset the default settings Go to System StatusRestoring the default settings Configuring the FortiGate unit Planning the FortiGate configurationNAT/Route mode Internet Router NAT/Route mode with multiple external network connectionsTransparent mode Preparing to configure the FortiGate unit in NAT/Route mode NAT/Route mode installationNAT/Route mode settings Go to System Network InterfaceDhcp or PPPoE configuration Using the web-based managerConfiguring basic settings Adding a default route To configure interfaces Go to System Network InterfaceTo add a default route Go to Router Static Using the command line interface Verifying the web-based manager configurationConfiguring the FortiGate unit to operate in NAT/Route mode Verify the connectionExample To configure DNS server settingsTo set the external interface to use DHCP, enter To set the external interface to use PPPoE, enterTo add a default route Connecting the FortiGate unit to the networks Configuring the networksTo connect the FortiGate unit Preparing to configure Transparent mode Transparent mode installationTransparent mode settings Administrator Password DNS SettingsTo verify the DNS server settings To change to Transparent mode using the CLIReconnecting to the web-based manager Connecting the FortiGate unit to your networkTo connect the FortiGate unit running in Transparent mode Set the date and time Next stepsUpdating antivirus and IPS signatures To update IPS signatures using the CLI Scheduling antivirus and IPS updatesTo enable schedule updates from the CLI Updating the IPS signatures from the CLIAdding an override server To add an override server using the CLINext steps Connecting a modem to the FortiGate-50A Configuring the modem interfaceSelecting a modem mode Redundant mode configurationStand alone mode configuration Mode must be standalone Interface name Configuring the modem for the FortiGate-50APhone-number CLI commands for the FortiGate-50ADead gateway detection Adding a Ping ServerAdding firewall policies for modem connections Setting up a wireless network Using a wireless networkRadio Frequency interface Positioning an Access PointUsing multiple APs to provide a constant strong signal Using multiple access pointsWireless Security Wireless Equivalent Privacy WEPWi-Fi Protected Access WPA Service Set Identifier FortiWiFi-50B operation modesAccess Point mode Additional security measuresFortiWiFi in Access Point mode Client modeSetting up the FortiWiFi-50B as an Access Point Changing the operating modeSet the Dhcp settings Configure the firewall policies To set the data security Go to System Wireless SettingsSet the security options To upgrade the firmware using the web-based manager Upgrading the firmware using the web-based managerFortiGate Firmware Upgrading to a new firmware versionTo upgrade the firmware using the CLI Upgrading the firmware using the CLIReverting to a previous firmware version For information, see the FortiGate Administration GuideTo revert to a previous firmware version using the CLI Reverting to a previous firmware version using the CLIExecute ping To install firmware from a system reboot Press Any Key To Download Boot Image Restoring the previous configuration Backup and Restore from the FortiUSB key To backup configuration using the CLIFortiUSB key Using the USB Auto-Install feature To restore configuration using the CLITo configure the USB Auto-Install using the CLI Testing a new firmware image before installing it Additional CLI commands for the FortiUSB keyTo test a new firmware image Testing a new firmware image before installing it Installing a backup firmware image Installing and using a backup firmware imagePress any key to enter configuration menu To install a backup firmware imageEnter File Name image.out Installing and using a backup firmware image CLI IndexWall mounting Web-based manager, connecting

Related manuals

Manual 272 pages 22.37 Kb