Fortinet 50A/50B, 100 manual CLI commands for the FortiGate-50A, Phone-number

Page 54

Configuring the modem for the FortiGate-50A

Configuring the modem interface

passwd2

Enter the password used to access the

No default.

<password_str>

specified dialup account.

 

passwd3

Enter the password used to access the

No default.

<password_str>

specified dial-up account.

 

Table 15: CLI commands for the FortiGate-50A

peer_modem1

If the modem at phone1 is Actiontec or

generic

{actiontec

AscendTNT, select that type, otherwise leave

 

ascendTNT

setting as generic. This setting applies to

 

models 50AM, 60M, and WiFi-50BM only.

 

generic}

 

 

peer_modem2

If the modem at phone2 is Actiontec or

generic

{actiontec

AscendTNT, select that type, otherwise leave

 

ascendTNT

setting as generic. This setting applies to

 

models 50AM, 60M, and WiFi-50BM only.

 

generic}

 

 

peer_modem2

If the modem at phone3 is Actiontec or

generic

{actiontec

AscendTNT, select that type, otherwise leave

 

ascendTNT

setting as generic. This setting applies to

 

models 50AM, 60M, and WiFi-50BM only.

 

generic}

 

 

phone1

Enter the phone number required to connect to

No default.

<phone-number>

the dial-up account. Do not add spaces to the

 

phone number. Make sure to include standard

 

 

special characters for pauses, country codes,

 

 

and other functions as required by your modem

 

 

to connect to your dial-up account.

 

 

 

 

phone2

Enter the phone number required to connect to

No default.

<phone-number>

the dialup account. Do not add spaces to the

 

phone number. Make sure to include standard

 

 

special characters for pauses, country codes,

 

 

and other functions as required by your modem

 

 

to connect to your dialup account.

 

 

 

 

phone3

Enter the phone number required to connect to

No default.

<phone-number>

the dialup account. Do not add spaces to the

 

phone number. Make sure to include standard

 

 

special characters for pauses, country codes,

 

 

and other functions as required by your modem

 

 

to connect to your dialup account.

 

 

 

 

redial

Set the maximum number of times (1-10) the

No default.

<tries_interger>

FortiGate unit dials the ISP to restore an active

 

connection on the modem interface. Select

 

 

none to allow the modem to redial without a

 

 

limit.

 

status {disable

Enable or disable modem support.

disable

enable}

 

 

username1

Enter the user name used to access the

No default.

<name_str>

specified dial-up account.

 

username2

Enter the user name used to access the

No default.

<name_str>

specified dialup account.

 

username3

Enter the user name used to access the

No default.

<name_str>

specified dialup account.

 

54

FortiGate-50A/50B, FortiWiFi-50B and FortiGate-100 FortiOS 3.0 MR4 Install Guide

01-30004-0265-20070831

Image 54
Contents Install G U I D E Trademarks Regulatory complianceContents Factory defaults Configuring the FortiGate unitConfiguring the modem interface Using a wireless networkFortiGate Firmware Index Reverting to a previous firmware versionFortiUSB key Introduction About the FortiGate unitFortiGate-50A FortiGate-100 FortiWiFi-50BFortiGate-50B Register your FortiGate unitFortiClient FortiGuard Subscription ServicesFortinet Family Products FortiMailFortiReporter About this documentFortiAnalyzer FortiBridgeDocument conventions Typographic conventionsFortinet documentation Fortinet Knowledge Center Customer service and technical supportFortinet Tools and Documentation CD Comments on Fortinet technical documentationCustomer service and technical support Installing the FortiGate unit Package ContentsPower Requirements Technical Specifications DimensionsWeight SpecificationsFortiWiFi-50B package contents FortiGate-100 package contents Front BackPowering on the FortiGate unit To power on the FortiGate unitMounting Power over Ethernet Command line interface Powering off the FortiGate unitConnecting to the FortiGate unit Connecting to the web-based managerFortiGate login To connect to the web-based managerBits per second 9600 Data bits Parity Connecting to the CLITo connect to the CLI Stop bits Flow controlQuick installation using factory defaults Quick configuration using default settingsGo to System Network Options Quick installation using factory defaults Factory defaults Factory default Dhcp server configuration Factory default NAT/Route mode network configurationAdministrative access Factory default Transparent mode network configurationFactory default firewall configuration Management IPFactory default protection profiles Restoring the default settings using the CLI Restoring the default settingsRestoring the default settings using the web-based manager To reset the default settings Go to System StatusRestoring the default settings Configuring the FortiGate unit Planning the FortiGate configurationNAT/Route mode NAT/Route mode with multiple external network connections Internet RouterTransparent mode NAT/Route mode settings NAT/Route mode installationPreparing to configure the FortiGate unit in NAT/Route mode Go to System Network InterfaceDhcp or PPPoE configuration Using the web-based managerConfiguring basic settings Adding a default route To configure interfaces Go to System Network InterfaceTo add a default route Go to Router Static Configuring the FortiGate unit to operate in NAT/Route mode Verifying the web-based manager configurationUsing the command line interface Verify the connectionTo set the external interface to use DHCP, enter To configure DNS server settingsExample To set the external interface to use PPPoE, enterTo add a default route Connecting the FortiGate unit to the networks Configuring the networksTo connect the FortiGate unit Transparent mode settings Administrator Password Transparent mode installationPreparing to configure Transparent mode DNS SettingsTo change to Transparent mode using the CLI To verify the DNS server settingsReconnecting to the web-based manager Connecting the FortiGate unit to your networkTo connect the FortiGate unit running in Transparent mode Next steps Set the date and timeUpdating antivirus and IPS signatures To enable schedule updates from the CLI Scheduling antivirus and IPS updatesTo update IPS signatures using the CLI Updating the IPS signatures from the CLITo add an override server using the CLI Adding an override serverNext steps Configuring the modem interface Connecting a modem to the FortiGate-50ASelecting a modem mode Redundant mode configurationStand alone mode configuration Configuring the modem for the FortiGate-50A Mode must be standalone Interface nameCLI commands for the FortiGate-50A Phone-numberAdding a Ping Server Dead gateway detectionAdding firewall policies for modem connections Using a wireless network Setting up a wireless networkPositioning an Access Point Radio Frequency interfaceUsing multiple access points Using multiple APs to provide a constant strong signalWireless Security Wireless Equivalent Privacy WEPWi-Fi Protected Access WPA Access Point mode FortiWiFi-50B operation modesService Set Identifier Additional security measuresClient mode FortiWiFi in Access Point modeSetting up the FortiWiFi-50B as an Access Point Changing the operating modeSet the Dhcp settings Configure the firewall policies To set the data security Go to System Wireless SettingsSet the security options FortiGate Firmware Upgrading the firmware using the web-based managerTo upgrade the firmware using the web-based manager Upgrading to a new firmware versionUpgrading the firmware using the CLI To upgrade the firmware using the CLIFor information, see the FortiGate Administration Guide Reverting to a previous firmware versionReverting to a previous firmware version using the CLI To revert to a previous firmware version using the CLIExecute ping To install firmware from a system reboot Press Any Key To Download Boot Image Restoring the previous configuration Backup and Restore from the FortiUSB key To backup configuration using the CLIFortiUSB key Using the USB Auto-Install feature To restore configuration using the CLITo configure the USB Auto-Install using the CLI Testing a new firmware image before installing it Additional CLI commands for the FortiUSB keyTo test a new firmware image Testing a new firmware image before installing it Installing and using a backup firmware image Installing a backup firmware imageTo install a backup firmware image Press any key to enter configuration menuEnter File Name image.out Installing and using a backup firmware image Index CLIWall mounting Web-based manager, connecting
Related manuals
Manual 272 pages 22.37 Kb