Eizo FS2332 user manual Other problems

Page 41

Other problems

Problem

Possible cause and remedy

15.The “Smoothing” on the Setting menu • You cannot choose “smoothing” when the screen is

“Screen” cannot be selected.

displayed in the following resolutions or settings.

 

--The resolution is 1920 × 1080

 

--Screen Size is “Normal”

16.The auto adjustment function does not • This function does not work during digital signal input.

work.

This function is intended for use on the Macintosh

 

 

and on AT-compatible PC running Windows. It does

 

 

not work properly when an image is displayed only

 

 

on a part of the screen (command prompt window, for

 

 

example) or when a black background (wallpaper, etc.)

 

 

is in use.

 

This function does not work correctly with some

 

 

graphics boards.

17. No audio output.

Check whether the stereo mini jack cable is connected

 

 

properly.

 

Check whether volume is set to 0.

 

Check the current external device and audio playback

 

 

software to see whether they are configured correctly.

 

If HDMI input is used, check the current external

 

 

device and the “Source” setting in the Setting menu

 

 

(see “3-2. Switching sound source for HDMI signal

 

 

input “Source”” (page 29)).

18.“ScreenManager Pro for LCD (DDC/CI)” • “ScreenManager Pro for LCD (DDC/CI)” does not run

does not run.

when a PC is connected to the HDMI input.

Check the setting for “DDC/CI” in the Setting menu.

 

(see ”3-4. Enabling/Disabling DDC/CI communication

 

“DDC/CI”” (page 30)).

During the demo mode of “Smart Resolution”, the

 

DDC/CI communication is disabled. “ScreenManager

 

Pro for LCD (DDC/CI)” does not run.

19.Will not change to the power saving mode • When all the conditions below are met, the monitor does not change to the power saving mode even if “Power Save” is set to “Enable”:

--“Power Save” for Sound is set to “Sound On” (“Audio Output” (page 34))

--In the mute state (“To mute the sound temporarily” (page 29))

In these cases, reset the mute.

Chapter 6 Troubleshooting 41

Image 41
Contents Page For USA-California Only Location of Caution StatementPage To use the monitor comfortably CleaningContents Limited Warranty Introduction FeaturesMonitor Controls and FunctionsReceivable Range of Remote Control Before Using Remote Control How to install batteryTo use ScreenManager Pro for LCDDDC/CI/EIZO ScreenSlicer Disk contents and software overviewEizo LCD Utility Disk Adjusting/Setting Displaying the Setting menuBasic operation of the Setting menu Basic Operations and FunctionsFunctions Main menu Setting ReferenceCompatible Resolutions/Formats Adjusting ScreensDigital Input DVI-D, Hdmi PC signal Digital Input Hdmi video signalWindows Setting the ResolutionWindows Vista Windows XPTo select the display mode Color Mode Adjusting ColorProcedure Display Modes PurposeAdjustable settings in each mode To perform advanced adjustmentsColor Mode FunctionTo adjust black level Black Level To adjust brightness BrightnessTo adjust contrast Contrast Adjustable range ProcedureAdjustable range To adjust the color saturation SaturationTo adjust hue Hue To adjust color temperature Temperature To adjust gain Gain To adjust gamma GammaTo set ContrastEnhancer ContrastEnhancer Still images show the same visual impressions To adjust the clarity of the image Smart ResolutionDigital Signal Input Screen AdjustmentAnalog Signal Input To set overdrive intensity OverdrivePrepare to use analog screen adjustment patterns Setting Procedures Perform the auto adjustmentTo eliminate vertical bars Clock To remove flickering or blurring PhaseTo correct the screen position Position Adjusting color gradationTo adjust color gradation automatically Auto Range Adjust Setting Function Analog Input D-Sub/Digital Input DVI-D, Hdmi PC signalScreen Size Changing Modify blurred characters or linesTo set the screen ratio Overscan Setting Function Screen DisplayAdjusting Volume Setting MonitorSwitching sound source for Hdmi signal input Source To turn the volume up/downLocking Buttons Key Lock To adjust the sound level Sound LevelEnabling/Disabling DDC/CI communication DDC/CI Setting Language Language Setting the Eizo Logo Display LogoChanging the authentication method for Hdmi signal input Method Input port Signal ErrorTo reset all adjustments to the default settings Reset Resetting the Monitor to the Default SettingsTo reset the color adjustments Color Reset Monitor Power Saving FunctionsSetting Power Saving Power Save Audio Output Setting Power Indicator Power IndicatorExiting the power saving mode Enabling/Disabling Auto Power-OFF Off Timer min Checking the power saving levelChecking the remaining time Cancelling procedureTime extension procedure Connecting Multiple External Devices Connecting CablesTo switch among input signals Connection examplesProblem Possible cause and remedy TroubleshootingImaging problems for both digital and analog Imaging problems for analog only Other problems Attach the arm or stand to the monitor How to Attach the Optional ArmReference Displaying Monitor Information Information Attaching the Stand baseSpecifications Main Default Settings Accessories Outside DimensionsGlossary Range Adjustment PhaseResolution TemperatureFollowing table shows factory preset analog signal timing Preset TimingLicense AppendixTrademark FCC Declaration of Conformity TCOHinweis zur Ergonomie Limited Warranty Limited WarrantyBegrenzte Garantie Garantie Limitée Garantía Limitada Garanzia Limitata Begränsad Garanti Περιορισμενη Εγγυηση Ограниченная Гарантия 有限责任保证书 关于电子信息产品污染控制标识 China Measures for RoHS Compliance in ChinaRoHS3rd Edition-December