Euphonix SH612 manual Jupiter Configuration, Serial Protocol

Page 26

Euphonix SH612 Studio Hub User Guide

Integration With Jupiter VM3000 Routers

 

 

 

 

1.Enter the MADI Routing menu using the SpinKnob.

2.For each MADI port, switch it to Non-Audio Deck and press Select to confirm the selection.

3.Connect an RS-422 cable (9-pin, male-to-male, straight-through) between the SH612’s Control port (bottom-right of the rear panel) and the Jupiter’s Serial port.

The VM3000 has eight Serial ports configured in pairs, 1/2, 3/4, 5/6, and 7/8.

4.Delegate one pair for the SH612.

Do not connect anything to the other port in that pair except another SH612.

4.2Jupiter Configuration

This section assumes you are familiar using the Jupiter Network Suite and Jupiter Con- figurator applications to edit Jupiter configuration sets. The examples and figures in this section document a basic configuration set with only the options necessary for the SH612 and VM3000 to work together.

NOTE: As the Jupiter manual suggests, we recommend adding rows to the end of the data tables, instead of inserting them in the middle, to reduce the risk of creating problems in a working setup.

To configure the Jupiter to control the SH612, open the Jupiter Configurator by opening the Jupiter Network Suite, click the JNS Tools button at the top, and click Configura- tion Editor. Then edit the configuration tables as described in the following sections (each of which is an entry in the Jupiter menu of the Jupiter Configurator).

4.2.1Serial Protocol

1.Configure the protocol for the port pair to which you connected the RS-422 ca- ble from the SH612 to be ESC (ES-Control)by selecting it from the dropdown menu.

Do not use ES-Bus, ES-Physical, or ES-Switch.

Figure 4-1Jupiter Serial Protocol dialog

2.The baud rate for the port pair should be automatically set to 38400 when ES- Control is selected. If not, select 38400 from the Baud 7/8 dropdown menu.

26

Image 26
Contents Euphonix SH612 Studio Hub User Guide Euphonix, IncMail info@euphonix.com Table of Contents Euphonix SH612 Studio Hub User Guide List of Figures Euphonix SH612 Studio Hub User Guide Features Introduction to the SH612Black and white video rate Power On SequencePAL/SECAM 25 fps Standard Operation Setting the Control PortModes of Operation ES ControlEuphonix SH612 Studio Hub User Guide Getting Started Status Display Front PanelLCD Display Menu DisplayArrow Keys Menu ControlsInfo EscapeSpinKnob Sample Rate Controls/IndicatorsSelect SpinKnobSample Rate Key Sample Rate LEDsMadi Indicators 6MADI ButtonsRear Panel Connectors 7SH612 Rear PanelPage Page Route Manager Configuration and PatchesConnections Euphonix SH612 Studio Hub User Guide Standalone Madi Routing 2Edit Current Configuration tab Under Studio Hub Input Connections, select Madi In #1Creating Custom Routes Under Studio Hub Output Connections, select Madi Out #3Select the Configurations and Patches tab Saving PatchesEuphonix SH612 Studio Hub User Guide Standalone Madi Routing Connections and Basic Setup Integration With Jupiter VM3000 RoutersSerial Protocol Jupiter ConfigurationDo not use ES-Bus, ES-Physical, or ES-Switch Switcher Description 2Jupiter Switcher Description dialogSwitcher Input 3Jupiter Switcher Input dialogSwitcher Output 4Jupiter Switcher Output dialogFinishing the Configuration 5 AES/Analog RoutingMenu Reference and Technical Specifications Menu ReferenceQuick Setup Menu Quick Setup MenuWord Clock In Oversample Sample Rate Setup MenuCustom Sample Rate Word Clock Out OversampleTime Code Setup Menu Select EscTime Code Offset Time Code ModeJam Sync Mode LTC Output Gain Time Code Free Wheel DurationDrift Warning Threshold Video Setup Menu SelectVitc Read Line # Bitc Window EnableVideo Jam Sync Vitc Write Line #Madi Setup Menu Madi Routing MenuAdd Route Madi Port DefinitionsEdit Route Store Routing MatrixRecall Routing Matrix Store SetupUtility Menu Control Port Recall SetupTransport Varispeed DisplaySH612 Technical Specifications SH612 Technical Specifications