Enterasys Networks A2H123-24 manual Electromagnetic Compatibility EMC

Page 5

ELECTROMAGNETIC COMPATIBILITY (EMC)

This product complies with the following: 47 CFR Parts 2 and 15, CSA C108.8, 89/336/EEC, EN 55022, EN 61000‐3‐2, EN 61000‐3‐3, EN 55024, AS/NZS CISPR 22, VCCI V‐3.

COMPATIBILIDAD ELECTROMÁGNETICA (EMC)

Este producto de Enterasys cumple con lo siguiente: 47 CFR Partes 2 y 15, CSA C108.8, 89/336/EEC, EN 55022, EN 55024, EN 61000‐3‐2, EN 61000‐3‐3, AS/NZS CISPR 22, VCCI V‐3.

ELEKTRO- MAGNETISCHE KOMPATIBILITÄT ( EMC )

Dieses Produkt entspricht den folgenden Richtlinien: 47 CFR Parts 2 and 15, CSA C108.8, 89/336/EEC, EN 55022, EN 61000‐3‐2, EN 61000‐3‐3, EN 55024, AS/NZS CISPR 22, VCCI V‐3.

HAZARDOUS SUBSTANCES

This product complies with the requirements of European Directive, 2002/95/EC, Restriction of Hazardous Substances (RoHS) in Electrical and Electronic Equipment.

EUROPEAN WASTE ELECTRICAL AND ELECTRONIC EQUIPMENT (WEEE) NOTICE

In accordance with Directive 2002/96/EC of the European Parliament on waste electrical and electronic equipment (WEEE):

1.The symbol above indicates that separate collection of electrical and electronic equipment is required and that this product was placed on the European market after August 13, 2005, the date of enforcement for Directive 2002/96/EC.

2.When this product has reached the end of its serviceable life, it cannot be disposed of as unsorted municipal waste. It must be collected and treated separately.

3.It has been determined by the European Parliament that there are potential negative effects on the environment and human health as a result of the presence of hazardous substances in electrical and electronic equipment.

4.It is the users’ responsibility to utilize the available collection system to ensure WEEE is properly treated.

For information about the available collection system, please go to http://www.enterasys.com/services/support/ or contact Enterasys Customer Support at 353 61 705586 (Ireland).

iii

Image 5
Contents SecureStack A2 Page Page Regulatory Compliance Information Electromagnetic Compatibility EMC Supplement to Product Instructions Vcci Notice Declaration of Conformity Enterasys NETWORKS, INC. Firmware License Agreement Viii Page Page Contents Figures Tables Xiv Who Should Use This Guide About This GuideRelated Documents How to Use This GuideFollowing conventions are used in this guide Conventions Used in This GuideSupport@enterasys.com Getting HelpOverview A2H123-24 SwitchA2H123-24 Stackable Switch Switch Configuration Using WebView Redundant Power Supply CapabilityConnectivity ManagementStandards Compatibility Lanview Diagnostic LEDsSwitch Configuration Using CLI Commands 10BASE-T Network Network Requirements1000BASE-T Network 100BASE-TX Network100BASE-FX Network Hardware Installation Required Tools Considerations Prior to InstallationUnpacking the Switch Installing the Rubber Feet Installing the Switch on a Flat SurfaceChassis Bottom, Rubber Feet Placement Area Guidelines for Switch Installation on Flat Surface Guidelines for Flat Surface InstallationAttaching Brackets and Installing in Rack Rack Mounting the SwitchGuidelines for Rackmount Installation Attaching the Rackmount Brackets Connecting Stacking CablesStacking Cable Connections About SecureStack A2 Switch Operation in a Stack Configuring Switches in a StackInstalling a New Stackable System of Up to Eight Switches Recommended Procedures for New and Existing StacksAdding a New Switch to an Existing Stack AC Power Connecting AC and RPS-SYS PowerSwitch Rear View RPS coverplate Screw holes for coverplate C2RPS-SYS Redundant Power SystemStack Initialization Overview Connecting to Console Port for Local ManagementWhat Is Needed Parameter Setting Connecting to an IBM or Compatible DeviceConnecting an IBM PC or Compatible Connecting to a VT Series Terminal10 Connecting a VT Series Terminal Connecting to a ModemConnecting UTP Cables Connecting to the Network12 Connecting a UTP Cable Segment to RJ45 Port 13 Four-Wire Crossover Cable RJ45 Pinouts for 10/100BASE-TX 15 Eight-Wire Crossover Cable RJ45 Pinouts for 1000BASE-TX Connecting Fiber-Optic Cables to LC Ports 17 Cable Connection to LC Fiber-Optic Connectors Initial Logon to Switch Management Completing the InstallationCompleting the Installation Hardware Installation Troubleshooting Lanview LEDs of A2H123-24 Using LanviewLED 26/Stack Off RPS Configuration Guide for proper setup Troubleshooting ChecklistConfiguration Guide for the IP address Reset Switch Using the Reset SwitchSwitch Specifications SpecificationsPhysical Console Port Pinout Assignments Fiber-Optic SpecificationsRegulatory Compliance Torque Values