Eaton Electrical QSNAP Environmental Ratings, Approvals/Certifications, Catalog Numbering System

Page 8

Intelligent Technologies (IT.) QSNAP

February 2002

Environmental Ratings

The following environmental ratings apply to the QSNAP.

Table 3: Environmental Ratings

Category

Description

Specification

 

 

 

 

 

 

Transportation

Temperature

-50°C to 80°C [-58°F to 176°F]

 

 

 

 

Humidity

95% non-condensing

 

 

 

Storage

Temperature

-50°C to 80°C [-58°F to 176°F]

 

 

 

 

Humidity

95% non-condensing

 

 

 

Operating

Temperature

-30°C to 55°C [-22°F to 131°F]

 

 

 

 

Humidity

95% non-condensing

 

 

 

 

Altitude

Above 2000 meters [6600 feet] consult factory

 

 

 

 

Shock

15 g’s half-wave sinusoidal 11 msecs

 

 

 

 

Vibration

5 – 57.5 Hz (100 – 17 msecs) @ 0.3 mm SA

 

 

 

 

 

57.5 – 150 Hz (17 – 6.7 msecs) @ 0.35 mm SA

 

 

 

 

Enclosure

IP20

 

 

 

Approvals/Certifications

The following approvals and certifications apply to the QSNAP.

Table 4: Approvals/Certifications

Standard

Approval/Certification

UL

CE

CSA

UL508

CSAC22.2 No. 14-95

Catalog Numbering System

There is only one catalog number for QCPort connection to Eaton’s Cutler-Hammer Intelligent Technologies (IT.) Electromechanical Starters. These starters include those listed in Table 1 on Page 1.

The catalog number is QSNAP.

This part number includes the QSNAP and the starter interface board that connects the starter and the QSNAP.

Note: When ordering QSNAP for Full Voltage Reversing, consult factory for the QSNAP Auxiliary contact and jumper catalog numbers.

Note: When ordering a ground fault detector, consult factory for catalog number.

4

Pub. No. MN05001001E

Image 8
Contents Intelligent Technologies Important Notice Please Read Table of Contents List of Tables List of FiguresProduct Overview DescriptionQsnap Electromechanical Starter Connectivity Table Qsnap S751 Connectivity TableFeatures and Benefits Safety Environmental Ratings Approvals/CertificationsCatalog Numbering System Environmental RatingsPhysical Description Physical FeaturesDimensions Power Source Power RequirementsCurrent Source LoadQsnap Default Input Data from Qsnap Default Output Data to QsnapOperation Out of Box OperationTypical Application Typical Qsnap ApplicationEnhanced Features Standard FeaturesEnhanced Features Fault DefinitionData Description Input Assembly Data DefinitionsInput/Output Data Output Assembly Data Definitions Default Input DataDefault Output Data Status LED Truth TableStatus LED Qsnap Truth TableUsing CH Studio ConfigurationInstallation Set the Group IDSW1 Settings SW1 SettingsMount the IT. Qsnap to the Starter Starter Size/Available Auxiliary Locations on Mounted QsnapQsnap Alignment and Mounting Starter RJ-45 Wire the IT. Qsnap to the StarterTerminal Block Wiring Connect the Qsnap to QCPort QCPort ConnectionTroubleshooting and Maintenance TroubleshootingTroubleshooting Renewal PartsNumber Parameter Length Units Appendix a Qsnap ParametersConfiguration Parameters Data Parameters Number Parameter Units LengthPublication Description Intelligent Technologies IT. Publications and SupportIT. Publications Intelligent Technologies IT. Qsnap Page Eaton’s Cutler-Hammer Aftermarket Services Response network that gives new meaning to customer service