Eaton Electrical CA03310002E manual DC Power Supply Requirements @ 68F 20C see Note at left

	NEMA Contactors & Starters	11
September 2003	IT. Electro-Mechanical
	Technical Data and Specifications
Table 6. Specifications, continued

Description	Size 00, 0	Size 1	Size 2	Size 3, 4	Size 5
Finger Protection
Front	IP20	IP20	IP20	IP20	IP20
At Terminals	IP10	IP10	IP00	IP00	IP00
At Terminals with max.	IP20	IP10	IP10	IP00	IP00
size wire installed
Terminals L1, L2, L3/T1, T2, T3
1 Wire per Terminal	14 – 8 AWG	14 – 4 AWG	14 – 1 AWG	6 – 250 MCM	4 – 750 MCM
(stranded or solid)	(1.5 – 10 mm2)	(1.5 – 16 mm2)	(1.5 – 35 mm2)	(16 – 120 mm2)	(25 – 420 mm2)
2 Wires per Terminal	14 – 10 AWG	14 – 6 AWG	14 – 2 AWG	6 – 3/0 AWG	1/0 — 300 MCM
(stranded or solid)	(1.5 – 4 mm2)	(1.5 – 16 mm2)	(1.5 – 25 mm2)	(16 – 70 mm2)	(50 — 150 mm2)
Strip Length	.45" (11 mm)	.5" (12 mm)	.7" (18 mm)	.8" (21 mm)	1.5" (40 mm)
Torque (max.)	20 lb-in (2.2 Nm)	35 lb-in (4.0 Nm)	45 lb-in (5.0 Nm) for	250 lb-in (28 Nm)	550 lb-in (62 Nm)
	for 14 – 10 AWG	for 14 – 10 AWG	Single 14 – 8 AWG
	(1.5 – 6 mm2);	(1.5 – 6 mm2);	(1.5 – 10 mm2);
	25 lb-in (2.8 Nm) for	40 lb-in (4.5 Nm) for	100 lb-in (11 Nm) for
	8 AWG (10 mm2)	8 AWG (10 mm2);	Single 6 – 1 AWG
		45 lb-in (5.0 Nm) for	(16 – 35 mm2) and
		6 – 4 AWG	Dual Wire
		(16 mm2)	Combinations
Driver	2.5 mm Hex Key	3 mm Hex Key	5/32" (4 mm) Hex Key	5/16" (8 mm) Hex Key	5/16" (8 mm) Hex Key
Operation Performance
Coil Voltage (nominal)	24V DC	24V DC	24V DC	24V DC	24V DC
Coil Operating	20 – 28	20 – 28	20 – 28	20 – 28	20 – 28
Voltage Range (V DC)
Control Terminals
(- and +)	14 – 12 AWG	14 – 12 AWG	14 – 12 AWG	14 – 12 AWG	14 – 12 AWG
1 Wire per Terminal	(1.5 – 2.5 mm2)	(1.5 – 2.5 mm2)	(1.5 – 2.5 mm2)	(1.5 – 2.5 mm2)	(1.5 – 2.5 mm2)
(- and +)	14 AWG	14 AWG	14 AWG	14 AWG	14 AWG
2 Wires per Terminal	(1.5 mm2)	(1.5 mm2)	(1.5 mm2)	(1.5 mm2)	(1.5 mm2)
(P, F, R, 1, 2, 3)	22 – 12 AWG	22 – 12 AWG	22 – 12 AWG	22 – 12 AWG	22 – 12 AWG
1 Wire per Terminal	(0.5 – 2.5 mm2)	(0.5 – 2.5 mm2)	(0.5 – 2.5 mm2)	(0.5 – 2.5 mm2)	(0.5 – 2.5 mm2)
(P, F, R, 1, 2, 3)	18 – 14 AWG	18 – 14 AWG	18 – 14 AWG	18 – 14 AWG	18 – 14 AWG
2 Wires per Terminal	(0.75 – 1.5 mm2)	(0.75 – 1.5 mm2)	(0.75 – 1.5 mm2)	(0.75 – 1.5 mm2)	(0.75 – 1.5 mm2)
Torque (max.)	4.5 lb-in (.5 Nm)	4.5 lb-in (.5 Nm)	4.5 lb-in (.5 Nm)	4.5 lb-in (.5 Nm)	4.5 lb-in (.5 Nm)
Strip Length	.25 (7 mm)	.25 (7 mm)	.25 (7 mm)	.25 (7 mm)	.25 (7 mm)
Driver	.13 (3.5 mm) Flat	.13 (3.5 mm) Flat	.13 (3.5 mm) Flat	.13 (3.5 mm) Flat	.13 (3.5 mm) Flat
Temperature
Operating	-40° to +149°F	-40° to +149°F	-40° to +149°F	-40° to +149°F	-40° to +149°F
	(-40° to +65°C)	(-40° to +65°C)	(-40° to +65°C)	(-40° to +65°C)	(-40° to +65°C)
Storage	-58° to +176°F	-58° to +176°F	-58° to +176°F	-58° to +176°F	-58° to +176°F
	(-50° to +80°C)	(-50° to +80°C)	(-50° to +80°C)	(-50° to +80°C)	(-50° to +80°C)
Environmental
Shock/Vibration	15G/5G	15G/5G	15G/5G	15G/5G	15G/5G
Altitude	6600 FT (2000M)	6600 FT (2000M)	6600 FT (2000M)	6600 FT (2000M)	6600 FT (2000M)
Pull-In Time (mS) @ 24V
Excl. Debounce Time	15	15	25	30	70 – 200
Incl. Debounce Time	75	80	88	95	120 – 300
Dropout Time (mS) @ 24V
Excl. Debounce Time	5	5	12	15	50 – 150
Incl. Debounce Time	65	70	75	80	70 – 250

Use Class B 75°C copper wire only (or 90°C copper wire sized for 75°C operation per NEC).

Consult factory for higher ratings.

The Non-reversing Starter requires the use of all six mounting screws for the maximum rating.

Notes:

■Response time for Control Inputs = Debounce Time

■The time between operating forward and reverse must be greater than the Debounce Time.

Note: At other temperatures expressed in °C, for either inrush or sealed, use the 20°C value from the table in the following

Watts = W20 [1.1 – .005(T) and

Amps = A20 [1.1 – .005(T)]

For example, inrush requirements for a NEMA

Size 2 Starter at -25°C would be: Watts = 130 [1.1 – .005 (-25)] = 160 Amps = 5.4 [1.1 – .005 (-25)] = 6.6

Table 7. 24V DC Power Supply Requirements @ 68°F (20°C) (see Note at left)

Contactor/Starter Size		Sealed In		Inrush
Catalog	NEMA Size	Wattage	Amps	Wattage	Amps	Duration
Number						(mS)
N_11B_ _X3N	00, 0	3.7	.15	80	3.3	50
N_01B_ _ _3A	00, 0	3.2	.13	80	3.3	50
N_11C_ _X3N	1	4.2	.18	90	3.8	50
N_01C_ _ _3A	1	3.6	.15	90	3.8	50
N_ _1D_ _ _3_	2	5.0	.21	130	5.4	65
N_ _1E_ _ _3_	3, 4	5.6	.23	140	5.8	85
N_ _1F_ _ _3_	5	12.0	.50	200	8.3	250
N_01F_ _ _3_	5	13.0	.54	200	8.3	250

_ indicates missing digit/character of the Catalog Number; may have multiple values.

CA03310002E For more information visit: www.cutler-hammer.eaton.com