Digi 412, Edgeport/8rr, Edgeport/1, Edgeport/421, Edgeport/416, Edgeport/2c, 22c For Windows

Page 11

To install the USB stack and Edgeport drivers:

1.Insert the “Edgeport Driver” CD into your CD-ROM drive.

2.When the welcome dialog appears, click the “Install Driver” button. Once the driver installation program has begun, follow the on screen instructions.

3a. If you are installing drivers for the first time: An Information dialog informs you that the installation was successful. After clicking “OK”, the installation is complete.

3b. If you are replacing existing Edgeport drivers: Follow the on-screen instructions. Note that, before beginning the installation of the drivers, all applications with open ports must be closed and all USB devices unplugged. If you close all the applications and unplug all the USB devices, then you will not need to reboot for the new drivers to take effect immediately. If any applications are left open or USB devices plugged in, you may choose to abort the installation or to continue and be required to reboot before the upgrade can take effect.

Note that because Windows NT 4.0 is not Plug-and-Play, you will not see a pop-up dialog box indicating that new hardware has been found. You may verify correct installation with the Edgeport Utility (see page 12) or the USB Status Utility (Viewer), as described below.

The USB Status Utility can be accessed by clicking the USB icon in your system tray or by clicking on Start, Programs, Inside Out Networks Utilities, USB Status Utility. This utility lists all the USB devices installed on your PC and provides other relevant information for each device. You may also use this utility to create a log file.

For Windows 95

1.After connecting the USB cable, the Update Device Driver Wizard dialog appears. Click "Next" to continue.

2.Insert the "Edgeport Driver" CD into your CD-ROM drive.

3.After Windows fails to locate the drivers on your floppy disk drive, click "Other Locations...".

4.When the Select Other Location dialog appears, type <CD drive letter>:\Win95 and click "OK".

5.Confirm that Windows has found the correct driver location and click "Finish".

6.When Windows prompts you for the driver disk, click "OK".

7.At the next Windows prompt, type <CD drive letter>:\Win95 and click "OK".

Installation is complete when no more dialogs appear. Your new COM port(s), numbered sequentially following the existing ports in your system, is/are ready.

Edgeport Installation Guide (90000403 Rev. D) – Page 9

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Edgeport Table of Contents Edgeport Products Edgeport/8rr RJ-12 Pin Assignments Cabling EdgeportEdgeport/8r RJ-45 Pin Assignments For Windows 98, CE, SE, Me, 2000 and XP Users Installing the Hub DriversEdgeport/21 Edgeport/42, Edgeport/421 For Windows 95 UsersFor Windows 95, 98, CE, SE, Me, 2000, XP and NT Users Using the Printer PortEdgeport/412, Edgeport/416 Edgeport/2c For Windows 98, CE, SE, Me, 2000, and XP Users Installing the Printer PortEdgeport/21c, Edgeport/22c For Windows NT Edgeport Driver InstallationFor Windows XP, 2000, and 2003 Server For Windows 98, and MeFor Windows For All Edgeports except the Edgeport/1 System Status LightMounting Diagrams General Tab Edgeport Utility ProgramFor All Windows Operating Systems Edgeport Installation Guide 90000403 Rev. D Edgeport Installation Guide 90000403 Rev. D Edgeport Installation Guide 90000403 Rev. D Version Tab Advanced Tab Understanding Hubs Example of a Typical Hub ConfigurationFCC Regulation Part Declaration of Conformity DoC Regulatory & Other InformationFor U.S. Government use For non-U.S. Government useEuropean Community CE Mark Declaration of Conformity DOC Department of Communication DOC Notice Canada onlyEN55024 UL/CSA Safety InformationDigi International EN 55022 Class B 1994 w/A1
Top Page Image Contents