Installation, Electrical requirements | KitchenAid 8301169 manual

Electrical requirements

If codes permit and a separate ground wire is used, it is recommended that a qualified electrician determine that the ground path and wire gauge are in accordance with local codes.

Do not ground to a gas pipe.

Check with a qualified electrician if you are not sure the range is properly grounded.

Do not have a fuse in the neutral or ground circuit.

This range must be connected to a grounded metal, permanent wiring system.

A. A four-wire or three-wire, single phase, 240-volt, 60-Hz, AC-only electrical supply is required on a separate, 30- ampere circuit, fused on both sides of the line. A time-delay fuse or circuit breaker is recommended. The fuse size must not exceed the circuit rating of the range specified on the model/serial rating plate located on the horizontal surface below the control panel.

B. Wire sizes and connections must conform to the requirements of the National Electrical Code ANSI/NFPA 70 – latest edition*, or CSA Standards C22.1- 94, Canadian Electrical Code, Part 1 and C22.2 No. 0-M91 - latest edition** and all local codes and ordinances.

C. The range should be connected directly to the fused disconnect or circuit breaker box through flexible, armored or non-metallic sheathed, copper cable. The flexible, armored cable extending from the fuse box or circuit breaker box should be connected directly to the junction box.

D. Locate the junction box to allow as much slack as possible between the junction box and the range so that the range can be moved if servicing is ever necessary. Do not cut the conduit.

E. A U.L.- or CSA-listed conduit connector must be provided at each end of the power supply cable (at the cooktop and at the junction box).

F. Connection at connection block must be copper wire only.

If the house has aluminum wiring, follow the procedure below:

a)Connect the aluminum wiring to the copper wiring using special connectors designed and Underwriters Laboratories-listed for joining copper to aluminum. Follow the electrical connector manufacturer’s recommended procedure.

b)Aluminum/copper connection must conform with local codes and industry- accepted wiring practices.

Copies of the standards listed may be obtained from:

*National Fire Protection Association One Batterymarch Park

Quincy, Massachusetts 02269

**CSA International

8501 East Pleasant Valley Road Cleveland, Ohio 44131-5575

Installation

WARNING

Excessive Weight Hazard

Use two or more people to move and install range.

Failure to do so can result in back or other injury.

1. Put on safety glasses and gloves. Remove shipping materials, tape and protective film from range. Keep shipping pallet under range. Unpack the burner grates, burner caps, simmer plate, grille grate, drip tray, spill guard, wave tray, wave plate, tile bezels, regulator, backguard and island trim. Items are either packaged in the range or on the range. Parts shipped with range depend on model ordered.

remove screws

bottom vent

2. Remove the bottom vent by removing the 2 screws on each side of the top of the bottom vent, Slide the vent

down and pull toward you. Carefully lay this part to the side to avoid scratching the stainless steel.

3. Lay a piece of cardboard from side packing on the floor behind range. Using

2 people, firmly grasp each side of range. Lift range up about 3 inches (8 cm) and move it back until the range is off shipping pallet. Set range on cardboard to avoid damaging floor.

4. Carefully move range

close to the cabinet opening. Place the rack in oven. Place level on rack, first side to side; then front to back.

leveling leg sleeves

If the range is not level, adjust the feet up or down. Turn leveling leg sleeves to level range and to raise or lower range to the desired countertop height.

5. Choose the correct bracket for your installation.

•If the wall behind the range has no baseboard or a baseboard up to 3/8" (9.5 mm) thick, use the shorter 1"

(2.5 cm) anti-tip bracket.

•If the wall behind the range has a baseboard thicker than 3/8" (9.5 mm), use the longer 1-3/4" (4.4 cm) anti-tip bracket.

rear brace

write down this distance

Locate a stud in wall behind range. Measure distance from top of rear brace to floor. Add 5/16" (7.9 mm) to measurement to allow anti-tip bracket to slide over rear brace. Use this final measurement and mark a horizontal line on wall where stud is located.

8301169 specifications

The KitchenAid 8301169 is a versatile and essential tool for any kitchen enthusiast looking to enhance their cooking and baking experiences. Renowned for its robust construction and user-friendly design, this kitchen appliance highlights KitchenAid's commitment to quality and innovation.

One of the standout features of the KitchenAid 8301169 is its powerful motor, which delivers exceptional performance while mixing, kneading, or whipping ingredients. This motor is designed to handle even the thickest doughs with ease, ensuring consistent results every time. Its multipurpose design makes it perfect for a variety of culinary tasks, from preparing bread and pastries to whipping cream or blending sauces.

The appliance comes equipped with a user-friendly control panel that allows for precise speed adjustments. This flexibility is crucial for achieving the desired consistency in your mixtures, whether you are mixing delicate ingredients or heavy batters. The KitchenAid 8301169 also boasts a tilt-head design, which provides easy access to the mixing bowl and makes it simple to change attachments or scrape down the sides.

In terms of included accessories, the KitchenAid 8301169 features various attachments that enhance its versatility. This often includes a flat beater for general mixing, a dough hook for kneading, and a wire whip for aerating ingredients. Each tool is engineered for optimal performance, making it easier to create a range of recipes with professional results.

The build quality of the KitchenAid 8301169 is impressive, featuring a die-cast metal construction that not only adds durability but also adds a touch of elegance to kitchen decor. Its premium finish is easy to clean and maintains its appearance over time, making it a long-lasting addition to your culinary arsenal.

Another notable characteristic is the appliance's compatibility with a wide array of KitchenAid attachments, allowing for even greater functionality. From food grinders to pasta makers, these attachments can expand the capabilities of the KitchenAid 8301169, making it an all-in-one solution for various cooking needs.

Overall, the KitchenAid 8301169 combines performance, style, and innovation, making it a must-have for both amateur cooks and seasoned chefs. Its blend of power, versatility, and durable construction ensures it will be a valued partner in the kitchen for years to come. Whether you're preparing family meals or experimenting with new recipes, this appliance is equipped to meet the culinary challenges head-on.