Mark Levinson N 320S owner manual Basic Operation, Front Panel Overview, Power button

Page 17

2

Basic Operation

 

3

5

4

6

7

polarity

select

IR Receiver

mono

volume

PREAMPLIFIER

Nº 320S

power

setup

enter

display intensity

balance

mute

standby

 

1

8

9

10

11

12

2

The numbers in the Nº 320S front panel illustration shown above correspond to the numbered items in the Front Panel Overview section that begins below.

Front Panel Overview

2-1

 

Unless otherwise specified, the numbered items in this section indicate the commands the front panel performs during normal operating mode. Refer to Section 3: Setup Menu and Section 4: Controls & Modes for information about other commands the front panel performs.

1.power button

Powers the Nº 320S on and off when the supplied power cord is connected to the ~ac mains connector and an electrical outlet. When the Nº 320S is powered off, pressing the power button connects power to the ~ac mains connector and powers on the Nº 320S. When powered on, the Nº 320S automatically enters standby after completing the initialization sequence. When the Nº 320S is powered on, pressing the power button disconnects power from the ~ac mains connector and powers off the Nº 320S.

Note

Before operating the Nº 320S, make sure the ~ac mains connector label indicates the correct operating voltage (page 1-7) for the current location.

(continued)

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Nº 320S Preamplifier This triangle, which appears on your component Important Safety InstructionsCustomer Support Table of Contents Controls & Modes Troubleshooting & MaintenanceAppendix IndexDocumentation Conventions Getting Started Special Design FeaturesGetting Started Mark Levinson Nº 320S HighlightsIr input connector RS-232 port Installation ConsiderationsProduct Registration Unpacking Balance controlQuantity PlacementTo replace the remote control batteries Remote Control BatteriesWarm-Up & Break-In Period Power RequirementsContinuous Operation Quick Start GuideNever Make or Break Connections to the Nº 320S To begin using the Nº 320SQuick Start Guide Front Panel Overview Power buttonBasic Operation Select knob Standby button & LEDFront panel display Polarity LEDEnter button Volume knobSetup button & LED Mute button & LED Display intensity buttonBalance button & LED Rear Panel Overview ~ac mains connectorBasic Operation Stereo input connectorsStereo main output connectors Slave in communication ports Stereo record output connectorsTrigger output connector Phono ground connectorIr input connector Serial number labelNº 320S is compatible with LinkingMaking Link Connections Making Link Connections Link communication port names differ among Mark Levinson All slave chainsComponents. The Link communication port names used Table below correspond with the component listedTo create a slave chain that includes the Nº 320S Nº390S Nº360S Link ControlsIntensity DisplayStandby PlaybackOperation Considerations Remote Control OverviewStandby Setupenter Command OverviewSetup button IR transmitterSelect ± buttons Volume ± buttonsBalance button Polarity buttonDisplay button Mono buttonNº 320S Navigating the Setup Menu Setup MenuSetup Menu Setup buttonTo open the setup menu Enter buttonDefault Possible Parameter Setting Settings Name Select knob ± buttons Volume knobFactory-Default, Custom Set Inputs MenuName Set Inputs Menu ShortcutCustom Names List To shortcut to the Set Inputs menu for the selected inputActivates SSP surround sound processor mode, which UnusedRtoR No30, No30.5To customize the name of the selected input Character ListGain Nº 320S Setup MenuOffset Gain parameter should be set before the Offset parameterRec.Out Teach IR MenuCommand Description To teach Nº 320S IR commands to a learning remote control Mute Setup Menu ParametersMaxVol TrigStandby Controls & ModesWhen the OFF 0% illumination level is selected To set the sleep timerDisplay Intensity Controls & ModesTo adjust main output signal polarity To adjust display intensityPolarity BalanceControls & Modes Mark Levinson To toggle between mono and stereo playback To select the desired mono modeMono Playback To use the L + R balance control + R Balance Control TipTo use L R mono playback to align phono cartridge azimuth Phono Alignment TipSSP Surround Sound Processor Mode To activate and use SSP mode Saving Data No Power No Remote Control Operation 5Troubleshooting & MaintenanceTroubleshooting No IR Learning No Main Output No Record Output Audible Hum Troubleshooting & MaintenanceNº 320S To restore factory-default settings Restoring Factory-Default SettingsDo not Apply Liquid Directly to the Nº 320S Care & MaintenanceNº 320S Troubleshooting & Maintenance Appendix SpecificationsSpecifications are subject to change without notice Setting Connectors Crosstalk Residual Noise Frequency Response WeightAppendix Input Overload Input Impedance Output ImpedanceTop View DimensionsFront View Mute Polarity MaxVol Intensity Trig Balance Mono Playback Installation WorksheetIndex Index Nº320S Power consumption, Nº320S, A-1 Obtaining service, IBCPower requirements, Nº320S, 1-7 to Reel-to-reel players Remote controlWarm-up & break-in period, Nº320S, 1-7 to Troubleshooting, 5-1 to 5-3TUNER input name, 3-5tunersObtaining Service

N 320S specifications

The Mark Levinson N 320S is a standout in the field of high-performance audio, representing an exquisite blend of cutting-edge technology and timeless design. Known for its remarkable fidelity and expansive sound stage, this device appeals to audiophiles who demand nothing but the best from their sound systems.

One of the main features of the N 320S is its dual-mono architecture. This design ensures that both channels have separate power supplies, signal paths, and amplification stages, which minimizes crosstalk and enhances audio purity. The result is a stereo experience that is expansive and richly detailed, allowing listeners to appreciate the subtle nuances in their favorite music tracks.

The N 320S also incorporates advanced digital signal processing capabilities. With a high-resolution DAC (digital-to-analog converter), it supports various file formats, including top-tier high-resolution audio. This versatility means that whether listeners prefer streaming hi-fi music or playing from a local library, the N 320S can handle it all with ease, offering pristine sound quality.

Additionally, the inclusion of a proprietary Harman Logic 7 processing technology allows the N 320S to deliver an immersive surround sound experience from stereo sources. This capability transforms simple two-channel audio into an enveloping sound field, enhancing the listening experience for movies and concerts alike.

The build quality of the Mark Levinson N 320S further exemplifies its commitment to excellence. Constructed with premium materials and meticulous craftsmanship, it not only performs exceptionally but also looks stunning in any audio setup. The front panel features a sleek design with a large, easy-to-read display, and its intuitive controls ensure that users can navigate through settings effortlessly.

In terms of connectivity, the N 320S provides a multitude of input options, including analog and digital connections, as well as Bluetooth capabilities for wireless streaming. This wide range of inputs makes it highly versatile, allowing users to integrate it seamlessly into their existing audio systems.

Overall, the Mark Levinson N 320S is a testament to the brand's dedication to high-fidelity sound and innovative technology. With its impressive features and sophisticated design, it stands as a remarkable choice for those who seek an elite audio experience. Whether for music or cinema, the N 320S delivers in a way few others can, making it a prized addition to any audiophile's collection.
Top Page Image Contents