Mark Levinson N 320S Restoring Factory-Default Settings, To restore factory-default settings

Page 60

Troubleshooting & Maintenance

Mark Levinson

CLEAR SETUP?

5-4

(continued)

Restoring Factory-Default

Settings

Performing this procedure restores all parameters and user-defined controls to their factory-default settings. Before performing this procedure, it is recommended to record all custom settings on the Installation Worksheet (page A-4).

To restore factory-default settings:

1.Press and release the front panel power button to power off the Nº 320S. It is also recommended to power off all associated components.

2.Press and hold the front panel setup and display intensity buttons.

3.Still holding the setup and display intensity buttons, press and release the power button to power on the Nº 320S.

•The CLEAR SETUP? message will appear on the front panel display as shown to the left.

4.Choose one of the following:

•To restore factory-default settings, continue holding the setup and display intensity buttons for about 10 seconds. The FACTORY SETTINGS RESTORED message will blink on the front panel display as shown below when factory- default settings have been restored.

FACTORY

 

 

 

SETTINGS

 

 

 

RESTORED

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

•To cancel restoration of factory-default settings, release the setup and display intensity buttons. The CLEAR and CANCELLED messages will blink on the front panel display as shown below to indicate that restoration of factory default settings has been cancelled.

CLEAR

 

 

 

CANCELLED

 

 

 

 

 

 

 

 

5.Power on all associated components that were powered off in step 1.

Page 59 Page 61
Image 60
Page 59 Page 61
Contents Nº 320S Preamplifier Important Safety Instructions This triangle, which appears on your componentCustomer Support Table of Contents Troubleshooting & Maintenance Controls & ModesAppendix IndexDocumentation Conventions Special Design Features Getting StartedGetting Started Mark Levinson Highlights Nº 320SInstallation Considerations Ir input connector RS-232 portProduct Registration Unpacking Balance controlPlacement QuantityRemote Control Batteries To replace the remote control batteriesPower Requirements Warm-Up & Break-In PeriodQuick Start Guide Continuous OperationTo begin using the Nº 320S Never Make or Break Connections to the Nº 320SQuick Start Guide Power button Basic OperationFront Panel Overview Standby button & LED Select knobFront panel display Polarity LEDVolume knob Setup button & LEDEnter button Display intensity button Balance button & LEDMute button & LED ~ac mains connector Rear Panel OverviewStereo input connectors Stereo main output connectorsBasic Operation Stereo record output connectors Slave in communication portsPhono ground connector Trigger output connectorIr input connector Serial number labelLinking Making Link ConnectionsNº 320S is compatible with Making Link Connections All slave chains Link communication port names differ among Mark LevinsonComponents. The Link communication port names used Table below correspond with the component listedTo create a slave chain that includes the Nº 320S Link Controls Nº390S Nº360SDisplay IntensityStandby PlaybackRemote Control Overview Operation ConsiderationsCommand Overview Standby SetupenterSetup button IR transmitterVolume ± buttons Select ± buttonsPolarity button Balance buttonDisplay button Mono buttonNº 320S Setup Menu Navigating the Setup MenuSetup button Setup MenuTo open the setup menu Enter buttonSelect knob ± buttons Volume knob Default Possible Parameter Setting Settings NameFactory-Default, Custom Set Inputs MenuSet Inputs Menu Shortcut NameCustom Names List To shortcut to the Set Inputs menu for the selected inputUnused Activates SSP surround sound processor mode, whichRtoR No30, No30.5Character List To customize the name of the selected inputNº 320S Setup Menu GainOffset Gain parameter should be set before the Offset parameterTeach IR Menu Rec.OutCommand Description To teach Nº 320S IR commands to a learning remote control Setup Menu Parameters MuteMaxVol TrigControls & Modes StandbyTo set the sleep timer When the OFF 0% illumination level is selectedDisplay Intensity Controls & ModesTo adjust display intensity To adjust main output signal polarityPolarity BalanceControls & Modes Mark Levinson To select the desired mono mode Mono PlaybackTo toggle between mono and stereo playback + R Balance Control Tip To use the L + R balance controlPhono Alignment Tip To use L R mono playback to align phono cartridge azimuthSSP Surround Sound Processor Mode To activate and use SSP mode Saving Data 5Troubleshooting & Maintenance TroubleshootingNo Power No Remote Control Operation Troubleshooting & Maintenance No IR Learning No Main Output No Record Output Audible HumNº 320S Restoring Factory-Default Settings To restore factory-default settingsCare & Maintenance Nº 320S Troubleshooting & MaintenanceDo not Apply Liquid Directly to the Nº 320S Specifications Specifications are subject to change without noticeAppendix Crosstalk Residual Noise Frequency Response Weight Setting ConnectorsAppendix Input Overload Input Impedance Output ImpedanceDimensions Front ViewTop View Installation Worksheet Mute Polarity MaxVol Intensity Trig Balance Mono PlaybackIndex Index Nº320S Obtaining service, IBC Power consumption, Nº320S, A-1Power requirements, Nº320S, 1-7 to Reel-to-reel players Remote controlTroubleshooting, 5-1 to 5-3TUNER input name, 3-5tuners Warm-up & break-in period, Nº320S, 1-7 toObtaining Service

N 320S specifications

The Mark Levinson N 320S is a standout in the field of high-performance audio, representing an exquisite blend of cutting-edge technology and timeless design. Known for its remarkable fidelity and expansive sound stage, this device appeals to audiophiles who demand nothing but the best from their sound systems.

One of the main features of the N 320S is its dual-mono architecture. This design ensures that both channels have separate power supplies, signal paths, and amplification stages, which minimizes crosstalk and enhances audio purity. The result is a stereo experience that is expansive and richly detailed, allowing listeners to appreciate the subtle nuances in their favorite music tracks.

The N 320S also incorporates advanced digital signal processing capabilities. With a high-resolution DAC (digital-to-analog converter), it supports various file formats, including top-tier high-resolution audio. This versatility means that whether listeners prefer streaming hi-fi music or playing from a local library, the N 320S can handle it all with ease, offering pristine sound quality.

Additionally, the inclusion of a proprietary Harman Logic 7 processing technology allows the N 320S to deliver an immersive surround sound experience from stereo sources. This capability transforms simple two-channel audio into an enveloping sound field, enhancing the listening experience for movies and concerts alike.

The build quality of the Mark Levinson N 320S further exemplifies its commitment to excellence. Constructed with premium materials and meticulous craftsmanship, it not only performs exceptionally but also looks stunning in any audio setup. The front panel features a sleek design with a large, easy-to-read display, and its intuitive controls ensure that users can navigate through settings effortlessly.

In terms of connectivity, the N 320S provides a multitude of input options, including analog and digital connections, as well as Bluetooth capabilities for wireless streaming. This wide range of inputs makes it highly versatile, allowing users to integrate it seamlessly into their existing audio systems.

Overall, the Mark Levinson N 320S is a testament to the brand's dedication to high-fidelity sound and innovative technology. With its impressive features and sophisticated design, it stands as a remarkable choice for those who seek an elite audio experience. Whether for music or cinema, the N 320S delivers in a way few others can, making it a prized addition to any audiophile's collection.
Top Page Image Contents