Dell 2.3 manual Deploying The Omsa Agent Onto An ESXi System, Click Apply Changes

Page 36

NOTE: OpenManage agents are required on Dell hosts earlier than Dell PowerEdge 12th generation servers. Install OMSA using the OpenManage Integration for VMware vCenter or install manually to hosts prior to installing the OpenManage Integration for VMware vCenter. Details on manually installing the agents are at http:// en.community.dell.com/techcenter/systems-management/w/wiki/1760.openmanage-server-administrator- omsa.aspx.

To deploy the OMSA agent tar.gz on an ESX system with the required remote enablement setting (-c) option:

1.Run the OMSA agent installation script: srvadmin-install.sh-x-c

2.Start OMSA services: srvadmin-services.sh start

3.If the OMSA agent is already installed, make sure that it has remote enablement configuration (-c) option or theOpenManage Integration for VMware vCenter installation will not complete successfully. Reinstall it with the -c option and restart the service:

srvadmin-install.sh -c srvadmin-services.sh restart

Deploying The OMSA Agent Onto An ESXi System

Install the OMSA VIB on an ESXi system to gather inventory and alert information from the systems.

NOTE: OpenManage agents are required on Dell hosts earlier than Dell PowerEdge 12th generation servers. Install OMSA using the OpenManage Integration for VMware vCenter or install manually to hosts prior to installing the OpenManage Integration for VMware vCenter. Details on manually installing the agents are at http:// en.community.dell.com/techcenter/systems-management/w/wiki/1760.openmanage-server-administrator- omsa.aspx.

1.If not already installed, install the vSphere command line tool (vSphere CLI) from http://www.vmware.com.

2.Enter the following command:

Vihostupdate.pl -server <IP Address of ESXi host> -i -b OM-SrvAdmin-Dell- Web-6.3.0-2075.VIB-ESX41i_A00.8.zip

NOTE: It can take a few minutes for OMSA to install. This command requires a reboot of the host after it completes.

Setting Up An OMSA Trap Destination

All 11th generation of hosts must have OMSA configured.

NOTE: OMSA is only required on Dell servers earlier than 12th generation Dell PowerEdge servers.

To set up an OMSA trap destination:

1.Either use the link to the OMSA user interface found in Settings General, or navigate to the OMSA agent from a Web browser (https://<HostIP>:1311/).

2.Log in to the interface, and select the Alert Management tab.

3.Select Alert Actions and make sure that any events to be monitored have the Broadcast Message option set, so that the events will be sent out.

4.Select the Platform Events option at the top of the tab.

5.Click the grey Configure Destinations button, and click the Destination link.

6.Select the Enable Destination check box.

7.Enter the OpenManage Integration for VMware vCenter appliance IP address in the Destination IP Address field.

8.Click Apply Changes.

9.Repeat step 1 to step 8 to configure additional events.

36

Image 36
Contents Page Page Contents End-To-End Hardware Management Hardware ManagementConsole Administration Viewing Or Editing Hypervisor ProfilesTroubleshooting Configuring Network Settings101 104 Key Features OpenManage Integration for VMware vCenterInventory Dell platformsOpenManage Integration for VMware vCenter Features Security Roles and Permissions Data IntegrityAccess Control Authentication, Authorization, And Roles Dell Operation RoleDell Infrastructure Deployment Role Dell.InventoryUnderstanding Privileges Dell.DeployPage Page Configuration Tasks Using the Configuration Wizard Configuration Wizard Welcome OpenManage Integration for VMware vCenter HomeCreating a New Connection Profile Wizard Configuring Events And Alarms Wizard Setting Up a Proxy Server Wizard Scheduling Inventory Jobs WizardEnter the Proxy Port number Running a Warranty Retrieval Job Wizard Configuring the Deployment Credentials WizardSetting The Default Firmware Update Repository Wizard Enabling The Omsa Link WizardConfiguring NFS Shares Settings OverviewGeneral Settings Overview Enabling The Omsa Link Outside the Configuration Wizard Enable or Disable Server Warranty Expiration NotificationCreating a New Connection Profile To create a new connection profile Configuring Events And Alarms About Proxy Configuration Setting Up a Proxy ServerRunning a Warranty Retrieval Job Using The Http Proxy For Retrieving Web Based DataDell Management Center, select Settings → Warranty Schedule Running Inventory JobsSetting Up The Firmware Repository Viewing or Editing Deployment CredentialsDell Online Shared Network Folder Click Begin TestServer Security Settings For Deployment Enabling a Deployable Server White ListAdding Deployable Servers To a White List About Host, Bare Metal, and iDRAC Compliance Issues Running The Fix Non-Compliant vSphere Hosts WizardDeleting Deployable Servers From a White List Related InformationRunning The Fix Non-Compliant Bare Metal Server Wizard Downloading An ISO For Manual Firmware Updates IDRAC License ComplianceRe-checking Bare Metal Server Compliance Upgrading OpenManage Integration for VMware vCenter About OpenManage Integration for VMware vCenter LicensingUpgrading From a Trial Version To a Full Product Version Understanding Events And Alarms Configure Snmp Omsa trap destinations, if neededMonitoring the Datacenter And Host System Event DescriptionUnderstanding Omsa For 11th Generation Dell PowerEdge Hosts Deploying the Omsa Agent onto an ESX SystemDeploying The Omsa Agent Onto An ESXi System Click Apply ChangesVSphere Client Host Overview Viewing EventsHost Information Dell Online Services Host ActionsManagement Consoles Resetting iDRAC Under Host Actions, select iDRAC ResetAbout Inventory Schedule Modifying An Inventory Job ScheduleTo update the Details of Last Inventory Job, click Refresh Displaying The Inventory For a Single Host System in vCenterInventory And Licensing Viewing Host Power Monitoring Viewing Storage InventoryManaging Connection Profiles Viewing Or Editing An Existing Connection Profile Testing a Connection Profile Deleting a Connection ProfileUnderstanding System Event Logs In vSphere Client Host View Refreshing a Connection ProfileDisplaying Logs in Dell Management Center About Firmware Updates Displaying The Event Logs For An Individual HostDell ftp.dell.com Shared NetworkRunning The Firmware Update Wizard Select Update from repositoryFirmware Versions After October 14 Firmware Versions Older than July 29Enter maintenance mode, apply updates, and restart Apply updates on next rebootUpdating Older Firmware Versions Click Update Firmware Advanced Host Management Using vCenter Viewing Firmware Update Status for Clusters and DatacentersSetting Up Physical Server Front Indicator Light Warranty RetrievalUnder Host Actions, select Blink Indicator Light Server Based Management ToolsViewing Server Warranty Information For a Single Host Hardware Management PrerequisitesProvisioning Overview Understanding Deployment Job TimesServer States Within The Deployment Sequence Understanding How To Configure a Hardware Profile Downloading Custom Dell ISO ImagesConfiguration Creating a New Hardware ProfilePage Cloning a Hardware Profile Enabling Csior On a Reference ServerLocally RemotelyAbout Managing Hardware Profiles Viewing Or Editing a Hardware ProfileDuplicating a Hardware Profile Renaming a Hardware ProfileRefreshing An Updated Hardware Profile Creating a New Hypervisor ProfileManaging Hypervisor Profiles Vlan SupportViewing Or Editing Hypervisor Profiles Duplicating a Hypervisor ProfilesBuilding a New Deployment Template Renaming Hypervisor ProfileDeleting a Hypervisor Profile Refreshing Hypervisor ProfilesRunning The Deployment Wizard Duplicating Deployment TemplatesDeleting a Deployment Template Renaming a Deployment TemplateDeployment Wizard Global Settings Deployment Wizard Select ServersDeployment Wizard Deployment Templates Deployment Wizard Server Identification Deployment Wizard Connection Profile Deployment Wizard Scheduling JobsUnderstanding Job Queue Click Schedule servers for deploymentManaging Deployment Jobs Using The Deployment Job Queue Adding a Server ManuallyOn the Select Server tab, click Add Server Removing a Bare Metal Server On the Select Servers tab, click Remove ServersClick Remove Selected Servers Web-based Administration Console Managing vCenter Server ConnectionsRegistering a vCenter Server OpenManage Integration for VMware vCenter Requirements Click RegisterVersions of ESXi that should be supported on hosts managed VCenter sSupportModifying The vCenter Administrator Login Updating The SSL Certificates For Registered vCenter ServersVirtual Appliance Management Restarting The Virtual ApplianceUpdating a Repository Location And Virtual Appliance Downloading the Troubleshooting Bundle Setting Up The Http ProxySetting Up the NTP Servers Updating the Virtual Appliance Software VersionRestoring the Default Https Certificate Click Restore Default Certificate for Https CertificatesGenerating a Certificate Signing Request Uploading an Https CertificateSetting up Global Alerts Managing Backup And RestoreConfiguring Backup And Restore Scheduling Automatic Backups Performing An Immediate BackupRestoring The Database From a Backup Click Backup NowConfiguring Network Settings Changing The Virtual Appliance PasswordEnter the Current Admin Password and press Enter Understanding the vSphere Client ConsoleSetting The Local Time Zone Rebooting Virtual ApplianceResetting The Virtual Appliance To Factory Settings Refreshing the Console ViewPower on the OpenManage Integration version 2.3 appliance Migration Path to migrate from 1.6/1.7 toTroubleshooting Frequently Asked Questions FAQVersion Affected All Firmware link communication error FTP TCP Rmcp UDP/TCP Select the Enable Platform Event Filter Alerts check box Select Temperatures under Main System ChassisWhen I tried to use lockdown mode, it failed Set UserVars.CIMoemProviderEnabled to How Do I Force Removal of the Virtual Appliance?Go to https//vcenterserverIPAddress/mob My Firmware Update Failed. What Do I Do? My vCenter Registration Failed. What Can I Do?Bare Metal Deployment Issues Hardware Configuration FailureEnabling Auto-Discovery On a Newly Purchased System Auto-Discovery and Handshake PrerequisitesContacting Dell Virtualization-related Events For Dell PowerEdge Servers Event Name Description SeverityNo action Dell Memory Device Dell Processor sensor Error Threshold value Independent error condition Dell Storage Controller Dell Storage Array disk Array disk warning Dell Watchdog Power Watchdog Power cycle Error Module information Information Dell Integrated Dual SD Understanding Auto-Discovery Auto-Discovery PrerequisitesLog in to the Integrated Dell Remote Access Controller GUI You must have the iDRAC and host IP addressesEnter the iDRAC IP address into a browser You must have the iDRAC and host IP addresses