Clarion APX600.5 manual Installation, Mounting Precautions, Wiring Precautions

Page 11

APPLICATIONS

OWNER'SMANUAL

INSTALLATION

This section lists Mounting and Wiring Precautions for installing the Clarion APX600.5. These safeguards provide enough detail to successfully complete an installation. If you do not have the necessary skills, Clarion recommends consulting your authorized Clarion dealer for installation.

MOUNTING PRECAUTIONS

Although the Clarion APX600.5 incorporates heat sinks and protection circuits, mounting the amplifier in a tight space without any air movement can still damage internal circuitry over time. Choose a site that provides adequate ventilation around the amplifier. For easy system set-up, mount the amplifier so the front panel controls will be accessible after installation.

In addition, observe the following precautions:

1.For the most efficient cooling, mount the amplifier so cool air runs along the length of the fins rather than across them. Remember, any moving air will dissipate heat.

2.Mount the amplifier on a rigid surface. Avoid mounting to subwoofer enclosures or areas prone to vibration. Do not install the amplifier on plastic or other combustible materials.

3.Prior to drilling, make sure proposed mounting holes will not cut into the fuel tank, fuel lines, brake lines (under chassis), or electrical wiring.

WIRING PRECAUTIONS

Read all wiring precautions. If you are not sure of the connections, contact your authorized Clarion dealer.

1. Before installation, make sure the source unit Power switch is in the OFF position.

2. Disconnect the negative (-) lead of the battery before making any power

INSTALLATION

connections.

 

3. When making connections, be sure that each connection is clean and secure. Insulate final connections with electrical tape or shrink tubing. Failure to do so may damage your equipment.

4. A secure clean ground connection is critical to the performance of your Clarion amplifier. Use the shortest ground wire possible and securely connect to the car chassis to minimize resistance and avoid noise problems.

5. Add an external fuse on the amplifier’s positive (+) power lead and connect it as close as possible to the vehicle’s (+) battery terminal. Use a rating that equals the total current consumption at full output of all amplifiers in the system. Adding an external fuse will protect the electrical system from short circuits that can cause a fire.

11

Page 10 Page 12
Image 11
Page 10 Page 12
Contents Page Introduction About the Manual and WarrantyTable of Contents Putinroductiontitle HereInput Connections and Audio Control DescriptionHigh-pass/Low-pass Filter Controls ConnectionsCrossover Selection Switches Connections for Power and SpeakersUse this flow chart to set up the Crossover Switches Flow ChartApplications ApplicationsMid Bass Midrange Channel System Channels High-Pass Plus Sub Wiring Precautions InstallationMounting Precautions Electrical connections for the APX600.5 InstallationSetting the Bass Boost Setting the GainSetting the Crossover Final System Check TroubleshootingProduct Specs TroubleshootingAPX600.5-10Rev.1 02/01

APX600.5 specifications

The Clarion APX600.5 is a versatile and high-performance 5-channel amplifier designed for car audio enthusiasts who demand exceptional sound quality and power. With its compact design and impressive specifications, this amplifier stands out as a reliable solution for enhancing the audio experience in any vehicle.

One of the main features of the APX600.5 is its power output. This amplifier delivers up to 600 watts of peak power, making it suitable for driving a combination of speakers and subwoofers effectively. The RMS power rating of 75 watts per channel at 4 ohms ensures that it can handle a variety of audio setups, allowing users to configure their systems as they see fit. Its ability to drive multiple channels simultaneously also makes it an efficient choice for those looking to maximize their audio setup without the need for multiple amplifiers.

The APX600.5 utilizes advanced Class D technology, which ensures a high level of efficiency and reduced heat generation compared to traditional Class A/B amplifiers. This not only contributes to the longevity and reliability of the unit but also means that users can enjoy high power output without the worry of overheating. Additionally, the amplifier features a compact design that maximizes space in the vehicle, making it easier to install even in tight locations.

Another noteworthy characteristic of the Clarion APX600.5 is its extensive crossover capabilities. The amplifier is equipped with adjustable high-pass and low-pass filters that allow for precise tuning of audio frequencies. This feature helps users achieve optimal sound quality and maintain clarity even at high volumes.

The built-in protection circuitry is another key technology that sets this amplifier apart. It features short-circuit protection, thermal overload protection, and DC offset protection, which ensures safe operation and prevents damage to both the amplifier and the connected speakers.

The APX600.5 also boasts an elegant design with a sleek finish that complements any vehicle's interior. The intuitive layout and clear terminal labeling simplify installation and adjustments, making it user-friendly.

In summary, the Clarion APX600.5 is an excellent choice for car audio enthusiasts seeking power, efficiency, and flexibility in a single compact amplifier. With its advanced technologies and features, it delivers top-notch audio performance that enhances any driving experience.
Top Page Image Contents