Clarion APX600.5 manual Final System Check, Troubleshooting

Page 14

APX600..5 Power System Amplifieri

FINAL SYSTEM CHECK

1.Start the engine and turn on the source unit. After a two-second delay,

slowly increase the Volume Control and listen to the audio. If you hear any noise, static, distortion or no sound at all, check the connections, and also refer to Troubleshooting. Depending on your system design, the levels may become quite loud even at low Volume Control settings. Until you get an “audio feel” of the system’s power, use care when adjusting controls.

2.Turn the Balance Controls to their extreme positions and listen to the results. The audio output should match the source unit settings. ( Example: source unit setting balance is left, audio from left speaker).

3.Increase the volume and verify that the amplifier reproduces audio (at full frequencies) without distortion. If you hear distortion, check the connections and verify that the Gain Control is set correctly. Another possibility is damaged speakers or under-powered speakers. Once again refer to Troubleshooting for additional help.

TROUBLESHOOTING

Problem

No Audio.

Solution

Low or no remote turn-on voltage. Check remote connections at amplifier and source unit.

 

Blown amplifier fuse. Replace with new fast-blow fuse (same rating).

 

Power wires not connected. Check battery and ground wiring at amplifier; also

 

check battery connections.

 

Speaker leads shorted. Check speaker continuity to ground, it should not show

TROUBLESHOOTING

a common ground.

Problem

 

Speakers not connected or are blown. Check speaker connections at amplifier,

measure coil impedance.

Problem

Audio cycles on and off.

Solution

Thermal protection circuits are shutting amplifier off. Check location for adequate ventilation; consult an authorized Clarion Audio Dealer.

Distorted audio.

Solution

Gain is not set properly, or damaged speaker cones. Review Setting Gain; inspect each speaker cone for signs of damage (i.e. frozen cone, burning smell, etc.)

14

SETTING THE GAIN

Page 13 Page 15
Image 14
Page 13 Page 15
Contents Page Putinroductiontitle Here About the Manual and WarrantyTable of Contents IntroductionDescription Input Connections and Audio ControlConnections High-pass/Low-pass Filter ControlsConnections for Power and Speakers Crossover Selection SwitchesFlow Chart Use this flow chart to set up the Crossover SwitchesApplications ApplicationsMid Bass Midrange Channel System Channels High-Pass Plus Sub Wiring Precautions InstallationMounting Precautions Installation Electrical connections for the APX600.5Setting the Bass Boost Setting the GainSetting the Crossover Troubleshooting Final System CheckTroubleshooting Product SpecsAPX600.5-10Rev.1 02/01

APX600.5 specifications

The Clarion APX600.5 is a versatile and high-performance 5-channel amplifier designed for car audio enthusiasts who demand exceptional sound quality and power. With its compact design and impressive specifications, this amplifier stands out as a reliable solution for enhancing the audio experience in any vehicle.

One of the main features of the APX600.5 is its power output. This amplifier delivers up to 600 watts of peak power, making it suitable for driving a combination of speakers and subwoofers effectively. The RMS power rating of 75 watts per channel at 4 ohms ensures that it can handle a variety of audio setups, allowing users to configure their systems as they see fit. Its ability to drive multiple channels simultaneously also makes it an efficient choice for those looking to maximize their audio setup without the need for multiple amplifiers.

The APX600.5 utilizes advanced Class D technology, which ensures a high level of efficiency and reduced heat generation compared to traditional Class A/B amplifiers. This not only contributes to the longevity and reliability of the unit but also means that users can enjoy high power output without the worry of overheating. Additionally, the amplifier features a compact design that maximizes space in the vehicle, making it easier to install even in tight locations.

Another noteworthy characteristic of the Clarion APX600.5 is its extensive crossover capabilities. The amplifier is equipped with adjustable high-pass and low-pass filters that allow for precise tuning of audio frequencies. This feature helps users achieve optimal sound quality and maintain clarity even at high volumes.

The built-in protection circuitry is another key technology that sets this amplifier apart. It features short-circuit protection, thermal overload protection, and DC offset protection, which ensures safe operation and prevents damage to both the amplifier and the connected speakers.

The APX600.5 also boasts an elegant design with a sleek finish that complements any vehicle's interior. The intuitive layout and clear terminal labeling simplify installation and adjustments, making it user-friendly.

In summary, the Clarion APX600.5 is an excellent choice for car audio enthusiasts seeking power, efficiency, and flexibility in a single compact amplifier. With its advanced technologies and features, it delivers top-notch audio performance that enhances any driving experience.
Top Page Image Contents