Clarion APX600.5 manual Setting the Gain, Setting the Crossover, Setting the Bass Boost

Page 13

INSTALLATION

OWNER'S MANUAL

SETTING THE GAIN

After completing the installation, follow these steps to set the Gain Control to tune the amplifier. Then perform the Final System Checks.

1.Turn the Gain Control all the way counter-clockwise.

2.Turn the vehicle’s Ignition Switch to the ON position. Then turn the ON/OFF Switch on the source units to the ON position. Set all Tone or Equalization Controls to “flat” positions and turn Loudness off.

Note: If the system uses an equalizer, set its frequency controls to “flat” positions.

3.Play a CD or Tape and set the Volume Control at 75% of full level.

4.Slowly increase the Gain Control. Stop when you hear a slight distortion of audio.

SETTING THE CROSSOVER

The Clarion APX600.5 features fully adjustable front and rear crossovers. To set the crossovers, follow these steps.

1.Using the X-Over Mode Selection Switch, select the desired mode - LP for Low Pass, HP for High Pass and FULL for Full Range.

2.Using the Freq (Hz) Control, select the desired frequency. If the desired frequency exceeds the range of the Freq (Hz) Selection Control, press the Crossover Frequency Multiplier Switch to increase the value by a multiplier of

10.•For example, 55Hz x 10 = 550Hz or 550Hz x 10 = 5.5kHz.

3.Repeat steps 1 and 2 for the front, sub, and rear crossovers.

SETTING THE BASS BOOST

 

1. Initially set the Subwoofer Bass Boost control to its full left position (i.e.

SETTING

0dB).

 

2. Listen to a variety of music styles (e.g. Rock, Rap, etc.) and slowly increase

 

the Bass Boost control until a noticeable increase in low bass response is

 

perceived.

THE

3. Slowly adjust the Bass Boost control (up or down) to realize the best bass

response.

GAIN

CAUTION: If you hear a “pop” (due to speaker over-excursion), lower the

Bass Boost to prevent speaker damage. If the system sounds muddy and

 

 

distorted (due to amplifier clipping), lower Bass Boost to avoid shutdown from

 

overheating.

 

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Page Table of Contents About the Manual and WarrantyPutinroductiontitle Here IntroductionInput Connections and Audio Control DescriptionHigh-pass/Low-pass Filter Controls ConnectionsCrossover Selection Switches Connections for Power and SpeakersUse this flow chart to set up the Crossover Switches Flow ChartApplications ApplicationsMid Bass Midrange Channel System Channels High-Pass Plus Sub Mounting Precautions InstallationWiring Precautions Electrical connections for the APX600.5 InstallationSetting the Crossover Setting the GainSetting the Bass Boost Final System Check TroubleshootingProduct Specs TroubleshootingAPX600.5-10Rev.1 02/01

APX600.5 specifications

The Clarion APX600.5 is a versatile and high-performance 5-channel amplifier designed for car audio enthusiasts who demand exceptional sound quality and power. With its compact design and impressive specifications, this amplifier stands out as a reliable solution for enhancing the audio experience in any vehicle.

One of the main features of the APX600.5 is its power output. This amplifier delivers up to 600 watts of peak power, making it suitable for driving a combination of speakers and subwoofers effectively. The RMS power rating of 75 watts per channel at 4 ohms ensures that it can handle a variety of audio setups, allowing users to configure their systems as they see fit. Its ability to drive multiple channels simultaneously also makes it an efficient choice for those looking to maximize their audio setup without the need for multiple amplifiers.

The APX600.5 utilizes advanced Class D technology, which ensures a high level of efficiency and reduced heat generation compared to traditional Class A/B amplifiers. This not only contributes to the longevity and reliability of the unit but also means that users can enjoy high power output without the worry of overheating. Additionally, the amplifier features a compact design that maximizes space in the vehicle, making it easier to install even in tight locations.

Another noteworthy characteristic of the Clarion APX600.5 is its extensive crossover capabilities. The amplifier is equipped with adjustable high-pass and low-pass filters that allow for precise tuning of audio frequencies. This feature helps users achieve optimal sound quality and maintain clarity even at high volumes.

The built-in protection circuitry is another key technology that sets this amplifier apart. It features short-circuit protection, thermal overload protection, and DC offset protection, which ensures safe operation and prevents damage to both the amplifier and the connected speakers.

The APX600.5 also boasts an elegant design with a sleek finish that complements any vehicle's interior. The intuitive layout and clear terminal labeling simplify installation and adjustments, making it user-friendly.

In summary, the Clarion APX600.5 is an excellent choice for car audio enthusiasts seeking power, efficiency, and flexibility in a single compact amplifier. With its advanced technologies and features, it delivers top-notch audio performance that enhances any driving experience.
Top Page Image Contents