Clarion manual Installation, Electrical connections for the APX600.5

Page 12

APX600.5 Power System Amplifier

6.Refer to Figure 9 when making electrical connections. Connect the amplifier’s positive (+) lead via a fuse directly to the positive (+) terminal on the battery. Do not connect this wire to the car’s fuse panel. Use red-insulated 8-gauge (or larger) wire for the amplifier’s positive (+) power lead and the same-gauge black insulated wire for the ground.

7.When replacing the amplifier’s fuse, always use one having the same current rating. Substituting a higher-rated fuse or a slow-blow type can result in serious damage to the amplifier.

8.Never ground the speakers to the vehicle chassis or body.

9.Make sure that your vehicle’s electrical system (alternator, battery, etc.) is capable of handling the additional load. If you are planning a multi-amplifier system, you may need to add a second battery and possibly upgrade the alternator with a higher-output rated model. Consult your authorized Clarion dealer for recommendations.

10.To avoid noise problems, run the amplifier’s positive (+) power lead along one side of the vehicle to the battery. Run the remote turn-on wire and RCA audio cables down the center, and route the speaker wires along the remaining side. If wires must cross, run them perpendicular to each other.

11.When creating passage holes for the power wire, use grommets to eliminate any sharp edges created during drilling. This will protect the wire from being nicked and causing a short circuit.

12.Extra cable can cause signal loss and act as an “antenna” for noise. Use only high-quality RCA cables that are no longer than necessary to make a direct connection with the source unit or equalizer.

INSTALLATION

Figure 9 - Electrical connections for the APX600.5

12

INSTALLATION

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Page About the Manual and Warranty Table of ContentsPutinroductiontitle Here IntroductionDescription Input Connections and Audio ControlConnections High-pass/Low-pass Filter ControlsConnections for Power and Speakers Crossover Selection SwitchesFlow Chart Use this flow chart to set up the Crossover SwitchesApplications ApplicationsMid Bass Midrange Channel System Channels High-Pass Plus Sub Installation Mounting PrecautionsWiring Precautions Installation Electrical connections for the APX600.5Setting the Gain Setting the CrossoverSetting the Bass Boost Troubleshooting Final System CheckTroubleshooting Product SpecsAPX600.5-10Rev.1 02/01

APX600.5 specifications

The Clarion APX600.5 is a versatile and high-performance 5-channel amplifier designed for car audio enthusiasts who demand exceptional sound quality and power. With its compact design and impressive specifications, this amplifier stands out as a reliable solution for enhancing the audio experience in any vehicle.

One of the main features of the APX600.5 is its power output. This amplifier delivers up to 600 watts of peak power, making it suitable for driving a combination of speakers and subwoofers effectively. The RMS power rating of 75 watts per channel at 4 ohms ensures that it can handle a variety of audio setups, allowing users to configure their systems as they see fit. Its ability to drive multiple channels simultaneously also makes it an efficient choice for those looking to maximize their audio setup without the need for multiple amplifiers.

The APX600.5 utilizes advanced Class D technology, which ensures a high level of efficiency and reduced heat generation compared to traditional Class A/B amplifiers. This not only contributes to the longevity and reliability of the unit but also means that users can enjoy high power output without the worry of overheating. Additionally, the amplifier features a compact design that maximizes space in the vehicle, making it easier to install even in tight locations.

Another noteworthy characteristic of the Clarion APX600.5 is its extensive crossover capabilities. The amplifier is equipped with adjustable high-pass and low-pass filters that allow for precise tuning of audio frequencies. This feature helps users achieve optimal sound quality and maintain clarity even at high volumes.

The built-in protection circuitry is another key technology that sets this amplifier apart. It features short-circuit protection, thermal overload protection, and DC offset protection, which ensures safe operation and prevents damage to both the amplifier and the connected speakers.

The APX600.5 also boasts an elegant design with a sleek finish that complements any vehicle's interior. The intuitive layout and clear terminal labeling simplify installation and adjustments, making it user-friendly.

In summary, the Clarion APX600.5 is an excellent choice for car audio enthusiasts seeking power, efficiency, and flexibility in a single compact amplifier. With its advanced technologies and features, it delivers top-notch audio performance that enhances any driving experience.
Top Page Image Contents