Datalogic Scanning 6000 manual IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E I/F Selection

Page 14

IBM 4683/84 • 4693/94 Port 9A, 9B, 9C, 9E I/F Selection

Scan this label to enable the IBM 468x/9x Port 9x interface.

IBM 4683/84 • 4693/94 Port 9A, 9B, 9C, 9E Settings

Data Format: Send As Code 39 — converts bar code data (UPC/EAN, add-ons, Code 93, Codabar, MSI/Plessey and Code 128) into Code 39 format before sending the data to the host.

These settings are for IBM 4683/84 • 4693/94 Port 9A, 9B, 9C, 9E inter- face ONLY.

Limit Command Set — is an option that causes the scanner to ignore 'enable scanner' and 'disable scanner' commands sent from the host.

Transmit Unsolicited Status1 — when enabled, this option causes the scanner to transmit a status message to the host upon receipt of an "SNRM".

SET

DATA FORMAT

----------------------------------------------

SEND AS CODE 39 ----------------

DON'T SEND AS CODE 39 --------

ENABLE LIMIT COMMAND SET -----

DISABLE LIMIT COMMAND SET -----

TRANSMIT UNSOLICITED STATUS ---

DON'T TRANSMIT UNSOLICITED STATUS ---

END ----------------------------------------------

1 For this IBM interface, the setting for Unsolicited Status is normally Disabled.

10

QuickScan 6000/6000 Plus

Image 14
Contents QuickScan 6000/6000 Plus Datalogic Scanning, Inc Contents Sample Bar Codes SymbologiesAdditional Information Understanding the Basics Integrating Peripherals With Host SystemsSoftware Changing InterfacesHardware RS-232 Wand Emulation Keyboard WedgeProgramming Overview Customizing Your Scanner OperationWhat Is Programming Mode? How To Program Using Bar CodesScanner Response When In Programming Mode Programming SessionReturn to Factory Settings If You Make a MistakeWhere To Go From Here Send AS Code Dont Send AS Code IBM 4683/84 4693/94 Port 5B SettingsIBM 4683/84 4693/94 Port 5B Interface Selection ENDIBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E Settings IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E I/F SelectionIBM 4682/92 Port E Settings IBM 4682/92 Port E Interface SelectionSNI Ocia Interface Selection Datalogic OCIA1 Interface SelectionNCR Ocia Nine Bit long format Interface Selection Enable Disable END Ocia OptionsTransmit in C39 Wand Emulation SettingsWand Emulation Interface Selection LOW High Transmit PRE-NOISERS-232 Communication Parameters RS-232 Interface SelectionSNI RS-232 Interface Selection Baud Rate Data Format TableData Format Settings None Even ODD Mark Space ONE TWO Seven Bits Eight Bits ENDHardware Control HandshakingEnable XON/ Xoff Disable XON/XOFF END SETDisable ACK/NAK These features available for QuickScan 6000 Plus onlyIntercharacter Delay = 90 Milliseconds = 100 Milliseconds END PC Keyboard Wedge Interface Selection Keyboard Wedge Communication ParametersT YPE Keyboard Attached Enable Disable END PC Keyboard Wedge Connect to a Laptop/No Keyboard AttachedCaps Lock QuickScan 6000 Plus only SET Caps Lock OFF Caps Lock onCountry Mode QuickScan 6000 Plus only Country Mode QuickScan 6000 Plus only Spain Sweden Switzerland Japanese 106-KEY ENDIntercharacter Delay Intercharacter Delay RS-232 and Keyboard Wedge Interfaces Only Prefix & SuffixProgramming Guide SET SET Prefix Non-Symbology Specific ItemsSetting Non-Symbology Specific Prefixes SET SET Suffix Setting Non-Symbology Specific SuffixesEntering Programming Mode Setting a Single Character Prefix or Suffix Setting Prefix and/or Suffix CharactersONE Character only Ascii Character Set Industry Standard Label Identifiers all are prefixes Symbology-Specific Label I.DSetting Symbology-Specific Label Identifiers Label I.D Setting Symbology Specific Label Identifiers Label I.D Label I.D. Symbology Selection EAN-13 W/C128 ADD- on EAN-13 W/2 Digit ADD- onEAN-13 W/5 Digit ADD- on ODEHow to Set Single Character Label I.D This example 8 equals 38hexDisabling Label I.D. for a Specific Symbology Symbology Specific Label Identifiers CharactersEND Symbologies Symbology Options Overview Standard 2 of 5 must be enabled before Iata can be enabled Universal Symbology SelectionEnable All Symbologies Disable All Symbologies1 Symbology Selection SET Enable UPC/EAN Disable UPC/EAN Enable Code Disable CodeEnable IATA3 Disable Iata Enable Codabar Disable Codabar Enable Code Disable Code Enable MSI/PLESSEY Disable MSI/PLESSEYUPC/EAN Options Dont Expand END UPC/EAN ExpansionDont Expand EXPAND1 C128 and Custom Add-Ons Optional Required Disabled ENDUPC/EAN Add-Ons UPC Data Format Settings Price/Weight Check DigitEnable 4 Digit Check Enable 5 Digit Check Send NSD2 Dont Send NSD2 END Send Check DigitSend NSD1 Dont Send NSD1 Send Check DIGIT2 EAN Data Format Settings Code 39 Options Dont Compute Dont Transmit Enable Disable END CodeSetting Lengths END AIM Symbology ID Prefix Code 128 OptionsInterleaved 2 Interleaved 2 of 5 Label LengthsCheck Digit and Variable Length Label Selections Setting Minimum Label Length Setting Interleaved 2 of 5 Fixed and Minimum Label LengthsSetting Fixed Lengths Set FixedSET First Fixed Length Standard 2 Standard 2 of 5 Label LengthsCheck Digit and Variable Length Label Selections Setting Standard 2 of 5 Fixed and Minimum Label Lengths Standard 2 of 5 Fixed and Minimum Label Lengths 5 Fixed Abel Lengths Tandard Minimum Codabar Options Codabar Check Digit & Variable Length Codabar Start/Stop Character Format = abcd/abcd ENDEnable Fixed Codabar Fixed LengthCodabar SET Fixed Lengths MSI/Plessey Check Digit ONE Check Digit TWO Check Digits ENDMSI/Plessey Fixed Length MSI/PLESSEY SET Fixed Lengths General Features Good Read Beeper SettingsOFF Read Verification Universal Read VerificationVerify Code Read Verification by SymbologyVerify UPC-A Verify UPC-E Verify EAN-8 Verify EAN-13 Verify Interleaved 2 Low Power Mode Disable LOW Power IdleDebug Mode AutoSense Stand ModeNeed More Information? Host ProgrammingCreating MultiFunction Labels Appendix B Sample Bar Codes UPC-E QuickScan 6000/6000 Plus Default Wand Keyboard Symbology RS-232 I/F Code 128 Options Transmit Don’t Transmit Codabar Options ABCD/ABCD Page Australia
Related manuals
Manual 104 pages 21.33 Kb