Datalogic Scanning 6000 manual Ocia Options, Enable Disable END

Page 17

OCIA Options

Use these labels to change the settings as desired. The following brief descriptions explain each selection.

Beep if Not on File — when enabled requires the scanner to beep when a label is scanned that is not on file.

Host Commands — when enabled allows the scanner to accept commands directly from the host.

Intercharacter Delay — refers to a pause, if any, between each character before being sent to the host. This time delay is used to control the flow of data from the scanner, but it should not be required for most applications. When enabled, OCIA intercharacter delay is set at 70µs.

 

SET

IF FILE

 

EEP ON

 

B OT

 

 

N

 

HOST

OMMANDS

 

 

C

 

NTERCHARACTER

DELAY

 

I

 

 

 

 

 

----------------------------------------------

ENABLE -----------------------------

DISABLE -----------------------------

ENABLE -----------------------------

DISABLE -----------------------------

ENABLE -----------------------------

DISABLE -----------------------------

END ----------------------------------------------

Programming Guide

13

Page 16 Page 18
Image 17
Page 16 Page 18
Contents QuickScan 6000/6000 Plus Datalogic Scanning, Inc Contents Sample Bar Codes SymbologiesAdditional Information Integrating Peripherals With Host Systems Understanding the BasicsSoftware Changing InterfacesHardware Wand Emulation Keyboard Wedge RS-232Customizing Your Scanner Operation Programming OverviewHow To Program Using Bar Codes What Is Programming Mode?Programming Session Scanner Response When In Programming ModeIf You Make a Mistake Return to Factory SettingsWhere To Go From Here IBM 4683/84 4693/94 Port 5B Interface Selection IBM 4683/84 4693/94 Port 5B SettingsSend AS Code Dont Send AS Code ENDIBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E I/F Selection IBM 4683/84 4693/94 Port 9A, 9B, 9C, 9E SettingsIBM 4682/92 Port E Interface Selection IBM 4682/92 Port E SettingsSNI Ocia Interface Selection Datalogic OCIA1 Interface SelectionNCR Ocia Nine Bit long format Interface Selection Ocia Options Enable Disable ENDTransmit in C39 Wand Emulation SettingsWand Emulation Interface Selection Transmit PRE-NOISE LOW HighRS-232 Communication Parameters RS-232 Interface SelectionSNI RS-232 Interface Selection Data Format Table Baud RateNone Even ODD Mark Space ONE TWO Seven Bits Eight Bits END Data Format SettingsHandshaking Hardware ControlSET Enable XON/ Xoff Disable XON/XOFF ENDThese features available for QuickScan 6000 Plus only Disable ACK/NAKIntercharacter Delay = 90 Milliseconds = 100 Milliseconds END Keyboard Wedge Communication Parameters PC Keyboard Wedge Interface SelectionT YPE PC Keyboard Wedge Connect to a Laptop/No Keyboard Attached Keyboard Attached Enable Disable ENDSET Caps Lock OFF Caps Lock on Caps Lock QuickScan 6000 Plus onlyCountry Mode QuickScan 6000 Plus only Spain Sweden Switzerland Japanese 106-KEY END Country Mode QuickScan 6000 Plus onlyIntercharacter Delay Intercharacter Delay Prefix & Suffix RS-232 and Keyboard Wedge Interfaces OnlyProgramming Guide SET SET Prefix Non-Symbology Specific ItemsSetting Non-Symbology Specific Prefixes SET SET Suffix Setting Non-Symbology Specific SuffixesEntering Programming Mode Setting Prefix and/or Suffix Characters Setting a Single Character Prefix or SuffixONE Character only Ascii Character Set Industry Standard Label Identifiers all are prefixes Symbology-Specific Label I.DSetting Symbology-Specific Label Identifiers Label I.D Setting Symbology Specific Label Identifiers Label I.D Label I.D. Symbology Selection EAN-13 W/5 Digit ADD- on EAN-13 W/2 Digit ADD- onEAN-13 W/C128 ADD- on ODEThis example 8 equals 38hex How to Set Single Character Label I.DSymbology Specific Label Identifiers Characters Disabling Label I.D. for a Specific SymbologyEND Symbologies Symbology Options Overview Standard 2 of 5 must be enabled before Iata can be enabled Universal Symbology SelectionEnable All Symbologies Disable All Symbologies1 SET Enable UPC/EAN Disable UPC/EAN Enable Code Disable Code Symbology SelectionEnable IATA3 Disable Iata Enable MSI/PLESSEY Disable MSI/PLESSEY Enable Codabar Disable Codabar Enable Code Disable CodeUPC/EAN Options Dont Expand END UPC/EAN ExpansionDont Expand EXPAND1 C128 and Custom Add-Ons Optional Required Disabled ENDUPC/EAN Add-Ons UPC Data Format Settings Price/Weight Check DigitEnable 4 Digit Check Enable 5 Digit Check Send NSD2 Dont Send NSD2 END Send Check DigitSend NSD1 Dont Send NSD1 Send Check DIGIT2 EAN Data Format Settings Code 39 Options Code Dont Compute Dont Transmit Enable Disable ENDSetting Lengths END Code 128 Options AIM Symbology ID PrefixInterleaved 2 of 5 Label Lengths Interleaved 2Check Digit and Variable Length Label Selections Setting Fixed Lengths Setting Interleaved 2 of 5 Fixed and Minimum Label LengthsSetting Minimum Label Length Set FixedSET First Fixed Length Standard 2 of 5 Label Lengths Standard 2Check Digit and Variable Length Label Selections Setting Standard 2 of 5 Fixed and Minimum Label Lengths Standard 2 of 5 Fixed and Minimum Label Lengths 5 Fixed Abel Lengths Tandard Minimum Codabar Options Codabar Check Digit & Variable Length Format = abcd/abcd END Codabar Start/Stop CharacterCodabar Fixed Length Enable FixedCodabar SET Fixed Lengths ONE Check Digit TWO Check Digits END MSI/Plessey Check DigitMSI/Plessey Fixed Length MSI/PLESSEY SET Fixed Lengths Good Read Beeper Settings General FeaturesOFF Universal Read Verification Read VerificationVerify Code Read Verification by SymbologyVerify UPC-A Verify UPC-E Verify EAN-8 Verify EAN-13 Verify Interleaved 2 Disable LOW Power Idle Low Power ModeAutoSense Stand Mode Debug ModeNeed More Information? Host ProgrammingCreating MultiFunction Labels Appendix B Sample Bar Codes UPC-E QuickScan 6000/6000 Plus Default Wand Keyboard Symbology RS-232 I/F Code 128 Options Transmit Don’t Transmit Codabar Options ABCD/ABCD Page Australia
Related manuals
Manual 104 pages 21.33 Kb
Top Page Image Contents