SBC comm SBC-770 manual Copyright Notice, Acknowledgements

Page 3

Copyright Notice

This document is copyrighted, 1999. All rights are reserved. The original manufacturer reserves the right to make improvements to the products described in this manual at any time without notice.

No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of the original manufacturer. Information provided in this manual is intended to be accurate and reliable. However, the original manufacturer assumes no responsibility for its use, nor for any infringements upon the rights of third parties which may result from its use.

Acknowledgements

AMD is a trademark of Advanced Micro Devices, Inc. AMI is a trademark of American Megatrends, Inc.

Award is a trademark of Award Software International, Inc. Cyrix is a trademark of Cyrix Corporation.

IBM, PC/AT, PS/2, and VGA are trademarks of International Business Machines Corporation.

Intel and Pentium II are trademarks of Intel Corporation. Microsoft Windows® is a registered trademark of Microsoft Corp. SMC is a trademark of Standard Microsystems Corporation.

RTL is a trademark of Realtek Semi-Conductor Co., Ltd. C&T is a trademark of Chips and Technologies, Inc.

UMC is a trademark of United Microelectronics Corporation. ITE is a trademark of Integrated Technology Express, Inc. SiS is a trademark of Silicon Integrated Systems Corp.

VIA is a trademark of VIA Technology, Inc.

All other product names or trademarks are properties of their respective owners.

Part No. 2047770001 SBC-770 2nd Edition

Printed in Taiwan

July 1999

Image 3
Contents SBC-770 Page Acknowledgements Copyright NoticeAaeon Customer Services Message to the CustomerTechnical Support Product Warranty Packing list Dear Customer Contents Award Bios Setup Ethernet Software configuration Page General Information Highly integrated SBC IntroductionFeatures Standard SBC functions SpecificationsFlat Panel/CRT Interface Mechanical and environmental Board layout Board dimensions Installation Label Function Jumpers and connectorsCN1 Locating jumpers Locating connectors Setting jumpers CPU installing and upgrading Mounting the CPU and cooling Modules Step Supplementary information about Dimm Installing Dram DIMMsMemory Installation Procedures System MemoryCache memory LCD driving voltage select J4 Clear Cmos J2CPU frequency ratio select J6 System temperature thermal sensor J5Pentium II CPU jumper setting examples 450/100MHz 500/100MHz 550/100MHz LCD clock signal select J7 DOC address select J8 COM2 RS-232/422/485 select J10, J9 Power connectors PWR1, CN5 Power connector PWR1CPU fan power connector CN5 Hard drive LED CN2 Power LED and Keylock CN1External speaker CN3 Reset switch CN4Connecting the hard drive IDE hard drive connector CN7, CN8IDE hard drive connectors CN7, CN8 IrDA connector CN9 Parallel port connector CN10 Parallel port connector table CN10Parallel port IRQ Connecting the floppy drive Floppy drive connector CN12Floppy drive connector CN12 USB connector CN14 VGA display connector CN15 Display connectors CN15, CN6LCD display connector CN6 100Base-Tx Ethernet connector CN17 Serial ports CN16, CN11COM2 RS-232/422/485 serial ports CN11 Keyboard and PS/2 mouse connector CN18, CN13 DiskOnChip socket U34 DiskOnChip DOC 2000 Installation Award Bios Setup To Enter Setup Before Boot Press DEL KEY Starting setupThese keys helps you navigate in Setup Setup keysGetting help Case of ProblemsBios Main setup MenuPage Standard Cmos setup Hard Disks Award Bios Setup Drive a Drive B Pannel Base Memory Extended Memory Bios features setup Virus Warning Boot Sequence PS/2 Mouse Function Control Chipset features setup Sdram RAS-to-CAS Delay Sdram Precharge Control Memory Hole at 15M-16M Power management setup Power Management Determines the manner in which the monitor is blanked Standby Mode Reload Global Timer Events PNP/PCI configuration setup PNP OS Installed DMA n Assigned to Load Bios defaults/Load setup defaults Integrated peripherals setup Select Enabled only if your hard drives support block mode Select a DMA channel for the port Supervisor/User password setting Enter Password IDE HDD auto detection Save & exit setup Page Flat Panel/CRT Controller Display Drivers and Utilities Software drivers Hardware configurationBefore you begin Necessary prerequisitesWindows Driver installationDriver Installation Page Driver Installation Page Driver Installation Page Driver Installation Windows NT Windows NT Page Ethernet Software Configuration Ethernet software configuration Programming the Watchdog Timer Outportb0x443, 30 // set watchdog to 30 seconds How to program the Watchdog TimerDemo program