SBC comm SBC-770 manual DiskOnChip socket U34

Page 52

DiskOnChip socket (U34)

The DiskOnChip 2000 family of products provides a single chip solid-state flash disk in a standard 32-pin DIP package. The DiskOnChip 2000 is a solid-state disk with no moving parts, resulting in a significant reduction in power consumption and an increase in reliability. The DiskOnChip is a small plug and play Flash disk. It is easy to use. And it saves integration overhead.

The DiskOnChip 2000 family of products is available in capacities ranging from 2MB up to 144MB, unformatted. In order to manage the disk, the DiskOnChip 2000 includes the TrueFFS, M-Systems Flash File System proprietary software. The DiskOnChip 2000 package is pin-to-pin compatible with a standard 32-pin EPROM device.

OE /

pin

Description

Pin N umber

Direction

Note

Name

 

 

 

 

 

 

 

 

 

A0-A12

Address bus

4- 12,23,25-27

Inputs

 

 

 

 

 

 

A13-A16

Address bus

2,3,28,29

Inputs

1

 

 

 

 

 

D0- D7

Data bus

13- 15,17-21

I/O

 

 

 

 

 

 

CE/

C hip Enable

22

Input

 

 

 

 

 

 

OE/

Output Enable

24

Input

 

 

 

 

 

 

WE/

Write Enable

31

Input

 

 

 

 

 

 

NC

Not connected

1.30

 

2

 

 

 

 

 

VCC

Pow er

32

 

 

 

 

 

 

 

GND

Ground

16

 

 

 

 

 

 

 

Note 1: Pins A13 through A16 are not used by the MD2200. They are kept for socket backward compatibility with ED 1100 (DiskOnChip 1000)

Note 2: Pins 1 and 30 are not used by MD2200

Chapter 2 Installation 41

Image 52
Contents SBC-770 Page Copyright Notice AcknowledgementsMessage to the Customer Aaeon Customer ServicesTechnical Support Product Warranty Packing list Dear Customer Contents Award Bios Setup Ethernet Software configuration Page General Information Introduction Highly integrated SBCFeatures Specifications Standard SBC functionsFlat Panel/CRT Interface Mechanical and environmental Board layout Board dimensions Installation Jumpers and connectors Label FunctionCN1 Locating jumpers Locating connectors Setting jumpers CPU installing and upgrading Mounting the CPU and cooling Modules Step Installing Dram DIMMs Memory Installation ProceduresSystem Memory Supplementary information about DimmCache memory Clear Cmos J2 LCD driving voltage select J4System temperature thermal sensor J5 CPU frequency ratio select J6Pentium II CPU jumper setting examples 450/100MHz 500/100MHz 550/100MHz LCD clock signal select J7 DOC address select J8 COM2 RS-232/422/485 select J10, J9 Power connector PWR1 Power connectors PWR1, CN5CPU fan power connector CN5 Power LED and Keylock CN1 Hard drive LED CN2Reset switch CN4 External speaker CN3IDE hard drive connector CN7, CN8 Connecting the hard driveIDE hard drive connectors CN7, CN8 IrDA connector CN9 Parallel port connector table CN10 Parallel port connector CN10Parallel port IRQ Floppy drive connector CN12 Connecting the floppy driveFloppy drive connector CN12 USB connector CN14 Display connectors CN15, CN6 VGA display connector CN15LCD display connector CN6 Serial ports CN16, CN11 100Base-Tx Ethernet connector CN17COM2 RS-232/422/485 serial ports CN11 Keyboard and PS/2 mouse connector CN18, CN13 DiskOnChip socket U34 DiskOnChip DOC 2000 Installation Award Bios Setup Starting setup To Enter Setup Before Boot Press DEL KEYSetup keys These keys helps you navigate in SetupCase of Problems Getting helpMain setup Menu BiosPage Standard Cmos setup Hard Disks Award Bios Setup Drive a Drive B Pannel Base Memory Extended Memory Bios features setup Virus Warning Boot Sequence PS/2 Mouse Function Control Chipset features setup Sdram RAS-to-CAS Delay Sdram Precharge Control Memory Hole at 15M-16M Power management setup Power Management Determines the manner in which the monitor is blanked Standby Mode Reload Global Timer Events PNP/PCI configuration setup PNP OS Installed DMA n Assigned to Load Bios defaults/Load setup defaults Integrated peripherals setup Select Enabled only if your hard drives support block mode Select a DMA channel for the port Supervisor/User password setting Enter Password IDE HDD auto detection Save & exit setup Page Flat Panel/CRT Controller Display Drivers and Utilities Hardware configuration Software driversNecessary prerequisites Before you beginDriver installation WindowsDriver Installation Page Driver Installation Page Driver Installation Page Driver Installation Windows NT Windows NT Page Ethernet Software Configuration Ethernet software configuration Programming the Watchdog Timer How to program the Watchdog Timer Outportb0x443, 30 // set watchdog to 30 secondsDemo program