SBC comm SBC-770 manual Award Bios Setup

Page 9

IDE hard drive connectors (CN7, CN8)	30
Connecting the hard drive	30
IDE hard drive connectors (CN7, CN8)	31
IrDA connector (CN9)	32
Parallel port connector (CN10)	33
Parallel port IRQ	33
Parallel Port connector table (CN10)	33
Floppy drive connector (CN12)	34
Connecting the floppy drive	34
Floppy drive connector (CN12)	35
USB connector (CN14)	36
Display connectors (CN15, CN6)	37
VGA display connector (CN15)	37
LCD display connector (CN6)	38
Serial ports (CN16, CN11)	39
COM2 RS-232/422/485 serial prots (CN11)	39
100Base-Tx Ethernet connector (CN17)	39
Keyboard and PS/2 mouse connector (CN18, CN13) ...	40
DiskOnChip socket (U34)	41
DiskOnChip (DOC) 2000 Installation	42
Chapter 3: Award BIOS Setup	43
Starting setup	44
Setup keys	45
Getting help	46
In case of problem	46
Main setup menu	47
Standard CMOS setup	49
BIOS features setup	56
CHIPSET features setup	60
Power management setup	64
PNP/PCI congfiguration setup	69
Load BIOS defaults/Load setup defaults	72

Image 9

Contents SBC-770 Page Acknowledgements Copyright NoticeAaeon Customer Services Message to the CustomerTechnical Support Product Warranty Packing list Dear Customer Contents Award Bios Setup Ethernet Software configuration Page General Information Highly integrated SBC IntroductionFeatures Standard SBC functions SpecificationsFlat Panel/CRT Interface Mechanical and environmental Board layout Board dimensions Installation Label Function Jumpers and connectorsCN1 Locating jumpers Locating connectors Setting jumpers CPU installing and upgrading Mounting the CPU and cooling Modules Step Memory Installation Procedures Installing Dram DIMMsSystem Memory Supplementary information about DimmCache memory LCD driving voltage select J4 Clear Cmos J2CPU frequency ratio select J6 System temperature thermal sensor J5Pentium II CPU jumper setting examples 450/100MHz 500/100MHz 550/100MHz LCD clock signal select J7 DOC address select J8 COM2 RS-232/422/485 select J10, J9 Power connectors PWR1, CN5 Power connector PWR1CPU fan power connector CN5 Hard drive LED CN2 Power LED and Keylock CN1External speaker CN3 Reset switch CN4Connecting the hard drive IDE hard drive connector CN7, CN8IDE hard drive connectors CN7, CN8 IrDA connector CN9 Parallel port connector CN10 Parallel port connector table CN10Parallel port IRQ Connecting the floppy drive Floppy drive connector CN12Floppy drive connector CN12 USB connector CN14 VGA display connector CN15 Display connectors CN15, CN6LCD display connector CN6 100Base-Tx Ethernet connector CN17 Serial ports CN16, CN11COM2 RS-232/422/485 serial ports CN11 Keyboard and PS/2 mouse connector CN18, CN13 DiskOnChip socket U34 DiskOnChip DOC 2000 Installation Award Bios Setup To Enter Setup Before Boot Press DEL KEY Starting setupThese keys helps you navigate in Setup Setup keysGetting help Case of ProblemsBios Main setup MenuPage Standard Cmos setup Hard Disks Award Bios Setup Drive a Drive B Pannel Base Memory Extended Memory Bios features setup Virus Warning Boot Sequence PS/2 Mouse Function Control Chipset features setup Sdram RAS-to-CAS Delay Sdram Precharge Control Memory Hole at 15M-16M Power management setup Power Management Determines the manner in which the monitor is blanked Standby Mode Reload Global Timer Events PNP/PCI configuration setup PNP OS Installed DMA n Assigned to Load Bios defaults/Load setup defaults Integrated peripherals setup Select Enabled only if your hard drives support block mode Select a DMA channel for the port Supervisor/User password setting Enter Password IDE HDD auto detection Save & exit setup Page Flat Panel/CRT Controller Display Drivers and Utilities Software drivers Hardware configurationBefore you begin Necessary prerequisitesWindows Driver installationDriver Installation Page Driver Installation Page Driver Installation Page Driver Installation Windows NT Windows NT Page Ethernet Software Configuration Ethernet software configuration Programming the Watchdog Timer Outportb0x443, 30 // set watchdog to 30 seconds How to program the Watchdog TimerDemo program