SBC comm SBC-770 manual LCD display connector CN6

Page 49

LCD display connector (CN6)

CN6 is a 50-pin, dual-in-line header used for flat panel displays.

When the mainboard's power is applied, the control signal is low until just after the relevant flat panel signals are present.

Configuration of the VGA interface is done completely via the software utility. You do not have to set any jumpers.

LCD display connector (CN6)

Pin	Signal	Pin	Signal
1	+12 VDC	2	+12 VDC
3	GND	4	GND

5	+5 VDC	6	+5 VDC
7	ENAVEE	8	GND

9	P0	10	P1
11	P2	12	P3

13	P4	14	P5

15	P6	16	P7

17	P8	18	P9
19	P10	20	P11

21	P12	22	P13

23	P14	24	P15

25	P16	26	P17

27	P18	28	P19

29	P20	30	P21

31	P22	32	P23
33	P24	34	P25

35	SHF CLK	36	FLM (V SYS)

37	M	38	LP (H SYS)

39	GND	40	ENABKL
41	P26	42	P27

43	P28	44	P29

45	P30	46	P31

47	P32	48	P33
49	P34	50	P35

38 SBC-770 User Manual

Image 49

Contents SBC-770 Page Acknowledgements Copyright NoticeMessage to the Customer Aaeon Customer ServicesTechnical Support Product Warranty Packing list Dear Customer Contents Award Bios Setup Ethernet Software configuration Page General Information Highly integrated SBC IntroductionFeatures Standard SBC functions SpecificationsFlat Panel/CRT Interface Mechanical and environmental Board layout Board dimensions Installation Label Function Jumpers and connectorsCN1 Locating jumpers Locating connectors Setting jumpers CPU installing and upgrading Mounting the CPU and cooling Modules Step Memory Installation Procedures Installing Dram DIMMsSystem Memory Supplementary information about DimmCache memory LCD driving voltage select J4 Clear Cmos J2CPU frequency ratio select J6 System temperature thermal sensor J5Pentium II CPU jumper setting examples 450/100MHz 500/100MHz 550/100MHz LCD clock signal select J7 DOC address select J8 COM2 RS-232/422/485 select J10, J9 Power connector PWR1 Power connectors PWR1, CN5CPU fan power connector CN5 Hard drive LED CN2 Power LED and Keylock CN1External speaker CN3 Reset switch CN4Connecting the hard drive IDE hard drive connector CN7, CN8IDE hard drive connectors CN7, CN8 IrDA connector CN9 Parallel port connector table CN10 Parallel port connector CN10Parallel port IRQ Connecting the floppy drive Floppy drive connector CN12Floppy drive connector CN12 USB connector CN14 VGA display connector CN15 Display connectors CN15, CN6LCD display connector CN6 Serial ports CN16, CN11 100Base-Tx Ethernet connector CN17COM2 RS-232/422/485 serial ports CN11 Keyboard and PS/2 mouse connector CN18, CN13 DiskOnChip socket U34 DiskOnChip DOC 2000 Installation Award Bios Setup To Enter Setup Before Boot Press DEL KEY Starting setupThese keys helps you navigate in Setup Setup keysGetting help Case of ProblemsBios Main setup MenuPage Standard Cmos setup Hard Disks Award Bios Setup Drive a Drive B Pannel Base Memory Extended Memory Bios features setup Virus Warning Boot Sequence PS/2 Mouse Function Control Chipset features setup Sdram RAS-to-CAS Delay Sdram Precharge Control Memory Hole at 15M-16M Power management setup Power Management Determines the manner in which the monitor is blanked Standby Mode Reload Global Timer Events PNP/PCI configuration setup PNP OS Installed DMA n Assigned to Load Bios defaults/Load setup defaults Integrated peripherals setup Select Enabled only if your hard drives support block mode Select a DMA channel for the port Supervisor/User password setting Enter Password IDE HDD auto detection Save & exit setup Page Flat Panel/CRT Controller Display Drivers and Utilities Software drivers Hardware configurationBefore you begin Necessary prerequisitesWindows Driver installationDriver Installation Page Driver Installation Page Driver Installation Page Driver Installation Windows NT Windows NT Page Ethernet Software Configuration Ethernet software configuration Programming the Watchdog Timer Outportb0x443, 30 // set watchdog to 30 seconds How to program the Watchdog TimerDemo program