Sony CPD-E220 service manual Power Saving Function, Diagnosis

Page 3

CPD-E220/E215E/E220E

POWER SAVING FUNCTION

This monitor meets the power-saving guidelines set by VESA, ENERGY STAR, and NUTEK. If the monitor is connected to a computer or video graphics board that is DPMS (Display Power Management Signaling) compliant, the monitor will automatically reduce power consumption in three stages as shown below.

Power mode

Power consumption

1 (power)

 

 

 

indicator

 

 

 

 

normal

120 W

green

operation

 

 

 

 

 

 

 

1 standby

15 W

green and orange

 

 

 

alternate

 

 

 

 

2 suspend

15 W

green and orange

(sleep)*

 

 

alternate

 

 

 

 

3 active off**

3 W

orange

(deep sleep)*

 

 

 

 

 

 

power off

0 W

off

 

 

 

 

*“Sleep” and “deep sleep” are power saving modes defined by the Environmental Protection Agency.

**When your computer is in a power saving mode, MONITOR IS IN POWER SAVE MODE appears on the screen if you press any button on the monitor. After a few seconds, the monitor enters the power saving mode again.

DIAGNOSIS

This monitor is equipped with a self-diagnosis function. If there is a problem with your monitor or computer, the screen will go blank and the 1 (power) indicator will either light up green or flash orange. If the 1 (power) indicator is lit in orange, the computer is in power saving mode. Try pressing any key on the keyboard.

If all four color bars appear (white, red, green, blue), the monitor is working properly. Reconnect the video input cable and check the condition of your computer.

If the color bars do not appear, there is a potential monitor failure. Inform your authorized Sony dealer of the monitor’s condition.

MENU

RESET

1 (power) indicator

If the 1 (power) indicator is green

1Disconnect the video input cable or turn off the connected computer.

2Press the 1 (power) button twice to turn the monitor off and then on.

3Move the control button , for 2 seconds before the monitor enters power saving mode.

MENU

If the 1 (power) indicator is flashing orange

Press the 1 (power) button twice to turn the monitor off and then on.

If the 1 (power) indicator lights up green, the monitor is working properly.

If the 1 (power) indicator is still flashing, there is a potential monitor failure. Count the number of seconds between orange flashes of the 1 (power) indicator and inform your authorized Sony dealer of the monitor’s condition. Be sure to note the model name and serial number of your monitor. Also note the make and model of your computer and video board.

– 3 –

Image 3
Contents CPD-E220/E215E/E220E Leakage Test Safety CHECK-OUTDiagnosis Power Saving FunctionTiming Specification Table of Contents D Boards Removal DisassemblySection Cabinet RemovalPicture Tube Removal Service PositionBoard Removal Removal of ANODE-CAP Removing ProceduresHarness Location HV Hold Safety Related Adjustment#2 Section AdjustmentsConvergence Specification Section Diagrams ∝ -COM, Deflection Control DEFLECTION, HV, Power Supply Diagram Schematic Diagrams and Printed Board Waveforms Schematic Diagrams of D a, b, c, d Board Schematic diagram Aboard Bboard l CHV Schematic diagram Cboard Dboard l IRFU110 IRFU110A SemiconductorsExploded Views ChassisTRANSFORMER, Flyback REF.NO. Part NO. Description Remark REF.NO. Part no Picture TubePacking Materials 101 103 104 105Petp Film Electrical Parts ListCeramic ElectBEAD, Ferrite 0.45∝ H Jump WireRES-CHIP RES, Chip3KV PIN, Connector Terminal PINPLUG, Connector 1P Metalized Film 0.022 ∝ FMetalized Film 0.01∝ F ConnectorCAP, Film Metalized Film 0.022∝ FDiode SR1003 PIN, Connector 3PPLUG, Connector 7P AC SocketTransistor 2SD669AVC Transistor 2SC945-PTransistor 2SA733-QP IC LM358NCarbon Small 100K ResistorCarbon Small 1M Metal OxideCarbon Small 1.5M Carbon Small 560KMetal Oxide Film 150K Carbon Small 1.5KPFC X’FORMER TRANSFORMER, PowerRelay TRANSFORMER, Driver