Alloy Computer Products GSS-24T4SFP Web Management Home Overview, Configuration, Monitoring

Page 15

GSS Series User Manual

3.1 Web Management Home Overview

Once you have entered a valid password and logged into the switch the System Configuration page will be displayed, this is the default page, it will be displayed every time that you log into the switch.

On the left hand side of the screen you will see a menu structure used to Configure, Monitor and manage your switch. There are three main menu categories Configuration, Monitoring and Maintenance.

Configuration

•System – Displays system information including Model Name, Firmware Version, Hardware Version, MAC Address etc. Also used to configure IP and SNMP settings.

•Ports – Displays link status of each port and also used to configure port speed, flow control and jumbo frame settings.

•VLAN Mode – Used to select the VLAN mode. Modes available are Tag-Based, Port Based and Metro Mode.

•VLAN Group - Used to configure VLAN settings.

•Aggregation – Used to configure port trunk groups.

•LACP – Used to configure LACP (Link Aggregation Control Protocol) settings.

•802.1x – Used to configure 802.1x authentication settings.

•IGMP Snooping – Used to configure IGMP settings.

•Mirror – Used to configure Port Mirroring features.

•QoS – Used to configure QoS settings.

•Filter – Used to configure filtering features.

•Rate Limit – Used to configure Rate Limiting settings.

•Storm Control – Used to configure Storm Control settings.

•SNMP – Used to configure SNMP settings.

Monitoring

•Detailed Port Statistics – Used to view detailed traffic statistics on each port.

•LACP Status – Displays LACP status.

•RSTP Status – Displays RSTP status.

•IGMP Status – Displays IGMP status.

•Ping – Used to test connectivity between other network devices.

Maintenance

•Warm Restart – Used to restart the switch.

•Factory Default – Used to reset the switch to factory default settings.

•Software Upgrade – Used to upgrade the firmware in the switch.

•Configuration File Transfer– Used to backup and restore the configuration of the switch.

•Logout – Used to Logout of the web management.

Alloy Computer Products Pty Ltd Copyright ©2007

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents GSS Series 16/24 Port Gigabit Web Managed Switch Table of Contents Electronic Emission Notices Federal Communications Commission FCC StatementAustralian C-Tick Compliance Page Overview IntroductionKey Features ChecklistOverview of the GSS range of switches Front Panel of the GSS-24T4SFP User interfaces on the front panelGigabit Copper Ports LED IndicatorsUser interfaces on the rear panel System LED’sAlloy Part No Description Overview of the Optional SFP ModulesConnecting the SFP Mini-GBIC Module to the Chassis Starting the GSS Series SwitchesHardware and Cable Installation Installing Optional SFP Mini-GBIC ModulesCopper Ports Cable Installation Power OnFirmware Loading Multimode Fibre Cable and Modal Bandwidth Cabling RequirementsPage Subnet Mask Password adminMonitoring ConfigurationMaintenance Web Management Home OverviewSystem Information ConfigurationManagement Enable Jumbo PortsFlow Control Drop Frames after Vlan Mode Page Tag Based VLAN’s Vlan GroupIngress Filtering Page Port Based VLAN’s Page Metro Mode VLAN’s Aggregation Lacp Rstp System ConfigurationPage Radius Secret Port Admin Mode Port State Action 802.1x Parameters Re-authenticationIgmp Querying IgmpUnregistered Ipmc Flooding Igmp SnoopingPort Mirroring Quality of Service 802.1p Quality of ServiceDscp Value Quality of Service DscpFilter Rate Limit Storm Control Learn FramesFlooded Unicast Snmp Set SnmpSnmp Trap Snmp GetDetailed Statistics MonitoringLacp Status Rstp Status Igmp Status Ping Warm Restart MaintenanceFactory Default Software Upgrade Configuration Download Configuration File TransferLogout ƒ Network Interface ƒ MAC Address and Self-learning 8K MAC addressƒ Cable and Maximum Length Dimensions ƒ Diagnostic LEDƒ Power Requirement Ambient Temperature
Top Page Image Contents