Advantech DNS-3200 user manual Chassis Installation, Important Safety Guidelines

Page 29

2.2 Chassis Installation

2.2.1 Important Safety Guidelines

Warning!: This product shall only be accessed, assembled and serviced by technically qualified personnel or technicians.

To avoid personal injury and property damage, please read all the information provided in Chap- ter 1, and carefully follow all the Safety Guide- lines listed before accessing or servicing the DNS series or its components.

For your convenience, some safety steps are also listed below.

Safety Steps

Before accessing the chassis:

1.Use a grounded wrist strap designed to prevent static discharge when handling components.

2.Turn off all peripheral devices and turn off the power supply con- nected to the DNS series.

3.Unplug all power cords from the system or wall outlets.

4.Disconnect all the cables and label the cables for easy identifica- tion.

Removing the chassis covers:

After completing the above steps, you can remove the chassis covers and install components and devices into the chassis as described in this chap- ter.

1.Unlock and remove the screws and fasteners to remove the cover or components.

2.Save all the screws and fasteners for later use. (If necessary, label these screws or fasteners for easy identification.)

3.Follow the instructions given in this chapter to remove the chassis covers.

11

Chapter2

Image 29
Contents 3U Dual Intel Xeon Storage Server with 15 Sata Channels User’s ManualCopyright Acknowledgements Product Warranty 3 years FCC Class a Declaration of ConformityTechnical Support and Assistance FCC Class BPacking List Document FeedbackUnpacking Your Advantech DNS-3200 Safety Instructions Wichtige Sicherheishinweise Page Safety Precaution Static Electricity General Electrical Safety Guidelines General Safety Guidelines ESD Safety Guidelines Removing the chassis covers Operation Safety Guidelines Before accessing the chassisProduct Compliance Information Reinstalling the chassis coversBefore installing the chassis into a rack Electromagnetic Compatibility EMC-Emissions Product SafetyContents Chapter RAID Console Operations Introduction About the Product Hardware FeaturesSystem Protection Software FeaturesDefault layouts may vary depending on the num Front panel is as shown below Product AppearanceDNS-3200 Rear panel Panel Indicators DNS-3200 User’s Manual Chassis Description and Installation Chassis Description Contents of the Accessory KitSafety Steps Before accessing the chassis Chassis InstallationImportant Safety Guidelines Tools Needed Accessing the SCA Drive Tray and Installing a HDDProcedures For Triple Redundant Power Supply- 3 x PWS-0050M Procedure Accessing the 760W Power SupplyDNS-3200 User’s Manual Procedure for Installing Chassis Rails Before installing the Chassis railsDNS-3200 User’s Manual Rack Installation DNS-3200 User’s Manual Page DNS-3200 User’s Manual Page DNS-3200 User’s Manual Configuration Turning the system on for the first time Configuration SettingsPage DNS-3200 User’s Manual Page DNS-3200 User’s Manual 2 WSS2003 Activation DNS-3200 User’s Manual 31Chapter3 DNS-3200 User’s Manual Vol/numbers.nspx Intel PROSet Network configuration settingTest Online Active Network configuration Team ModeAdapter Fault Tolerance AFT Adaptive Load Balancing ALB Swap Fault Tolerance SFTDynamic Link Aggregation Static Link AggregationManaging Arrays and Disks Array States RAID Minimum Disk RequirementsUnderstanding Array and Disk States Offline Disk States Rescanning for Changes in State Starting and Stopping Tasks Dedicated Distributed Global Working with SparesAbout Sparing Options Using Distributed Sparing To add a distributed spare while creating an array Distributed Spare field, click EnabledTo add a distributed spare while transforming an array Using Dedicated SparingDistributed Spare field, click Disabled Page Using Global Sparing Bios Configuration Utility To enter the Bios Configuration Utility Using the Bios Configuration UtilityWhen to Use the Bios Configuration Utility Initializing Disks from the Bios Color Codes for the Bios Array Config UtilityTo initialize disks from the Bios Creating Arrays from the BiosTo create an array DNS-3200 User’s Manual Create an array To Delete an Array Deleting Arrays from the BiosSwapping Arrays from the Bios Swap arrays To swap arraysTo hide or Unhide an array Hiding or Unhiding Arrays from the BiosTo view disk details Viewing Disk Details from the BiosRescanning All Channels from the Bios Viewing Array Details from the BiosArray Number Type Size State Name Cache setting DOS size To view array detailsChanging Controller Options from the Bios Change controller options Continue Booting from the Bios DNS-3200 User’s Manual RAID Console Opera- tions RAID Console RAID Console OperationsRAID Console Management RAID list Disk State Area RAID State Area System I/O State DNS-3200 User’s Manual Page Mirror split as an advanced option Mirror split as a preset optionMirror Split Check Hide the newly Split off array Online RAID level migration Online RAID Level MigrationPage DNS-3200 User’s Manual System Maintenance System Protection & Repairs Operating System Split DNS-3200 User’s Manual Operating System Swap DNS-3200 User’s Manual Page DNS-3200 User’s Manual Operating System Repair DNS-3200 User’s Manual Page DNS-3200 User’s Manual Hardware Specifica- tions Table A.1 Hardware Specifications Appendix a Hardware SpecificationsEnvironment DNS-3200 User’s Manual