Advantech DNS-3200 user manual Swap Fault Tolerance SFT, Adaptive Load Balancing ALB

Page 55

Swap Fault Tolerance (SFT)

Function: SFT provides automated residue to the network interface card as a fault tolerance. With the two network ports connected to different switches, one is the primary network for normal team and the other is the backup and is usually not in the “On” state. If the primary online develops problems, the backup network will start and take over the team.

Network configuration:

1.Each network port must be connected to a different network switch.

2.The switch must have the Spanning Tree Protocol (STP) in “On” state.

Adaptive Load Balancing (ALB)

Function: ALB provides load balancing and fault tolerance to the net- work flow and uses the software to analyze the transmission load on each interface card. For the two network ports sharing the load balancing of the transmission load and received flow load balancing of the IP protocol, if one team develops problems, the other team will take over the task.

Network configuration:

1.The network ports must be connected to the same network switch.

2.All switches must be able to support ALB.

Note: ALB does not balance non-routable communica- tion protocols, such as NetBEUI and some other IPX* flows.

37

Chapter3

Image 55
Contents 3U Dual Intel Xeon Storage Server with 15 Sata Channels User’s ManualCopyright Acknowledgements Product Warranty 3 years FCC Class a Declaration of ConformityTechnical Support and Assistance FCC Class BUnpacking Your Advantech DNS-3200 Document FeedbackPacking List Safety Instructions Wichtige Sicherheishinweise Page Safety Precaution Static Electricity General Electrical Safety Guidelines General Safety Guidelines ESD Safety Guidelines Removing the chassis covers Operation Safety Guidelines Before accessing the chassisBefore installing the chassis into a rack Reinstalling the chassis coversProduct Compliance Information Electromagnetic Compatibility EMC-Emissions Product SafetyContents Chapter RAID Console Operations Introduction About the Product Hardware FeaturesSystem Protection Software FeaturesDefault layouts may vary depending on the num Front panel is as shown below Product AppearanceDNS-3200 Rear panel Panel Indicators DNS-3200 User’s Manual Chassis Description and Installation Chassis Description Contents of the Accessory KitImportant Safety Guidelines Chassis InstallationSafety Steps Before accessing the chassis Procedures Accessing the SCA Drive Tray and Installing a HDDTools Needed For Triple Redundant Power Supply- 3 x PWS-0050M Procedure Accessing the 760W Power SupplyDNS-3200 User’s Manual Procedure for Installing Chassis Rails Before installing the Chassis railsDNS-3200 User’s Manual Rack Installation DNS-3200 User’s Manual Page DNS-3200 User’s Manual Page DNS-3200 User’s Manual Configuration Turning the system on for the first time Configuration SettingsPage DNS-3200 User’s Manual Page DNS-3200 User’s Manual 2 WSS2003 Activation DNS-3200 User’s Manual 31Chapter3 DNS-3200 User’s Manual Vol/numbers.nspx Intel PROSet Network configuration settingTest Online Active Adapter Fault Tolerance AFT Team ModeNetwork configuration Adaptive Load Balancing ALB Swap Fault Tolerance SFTDynamic Link Aggregation Static Link AggregationManaging Arrays and Disks Understanding Array and Disk States RAID Minimum Disk RequirementsArray States Offline Disk States Rescanning for Changes in State Starting and Stopping Tasks About Sparing Options Working with SparesDedicated Distributed Global Using Distributed Sparing To add a distributed spare while creating an array Distributed Spare field, click EnabledDistributed Spare field, click Disabled Using Dedicated SparingTo add a distributed spare while transforming an array Page Using Global Sparing Bios Configuration Utility When to Use the Bios Configuration Utility Using the Bios Configuration UtilityTo enter the Bios Configuration Utility Initializing Disks from the Bios Color Codes for the Bios Array Config UtilityTo initialize disks from the Bios Creating Arrays from the BiosTo create an array DNS-3200 User’s Manual Create an array Swapping Arrays from the Bios Deleting Arrays from the BiosTo Delete an Array Swap arrays To swap arraysTo hide or Unhide an array Hiding or Unhiding Arrays from the BiosTo view disk details Viewing Disk Details from the BiosTo view array details Viewing Array Details from the BiosRescanning All Channels from the Bios Array Number Type Size State Name Cache setting DOS sizeChanging Controller Options from the Bios Change controller options Continue Booting from the Bios DNS-3200 User’s Manual RAID Console Opera- tions RAID Console Management RAID Console OperationsRAID Console RAID list Disk State Area RAID State Area System I/O State DNS-3200 User’s Manual Page Mirror Split Mirror split as a preset optionMirror split as an advanced option Check Hide the newly Split off array Online RAID level migration Online RAID Level MigrationPage DNS-3200 User’s Manual System Maintenance System Protection & Repairs Operating System Split DNS-3200 User’s Manual Operating System Swap DNS-3200 User’s Manual Page DNS-3200 User’s Manual Operating System Repair DNS-3200 User’s Manual Page DNS-3200 User’s Manual Hardware Specifica- tions Table A.1 Hardware Specifications Appendix a Hardware SpecificationsEnvironment DNS-3200 User’s Manual