Packard Bell M5850 manual Checking Jumper Settings, Setting Jumpers

Page 85

Checking Jumper Settings

This section explains how to set jumpers for correct configuration of the motherboard.

Do not over-tighten the screws as this can stress the motherboard.

Setting Jumpers

Use the motherboard jumpers to set system configuration options. Jumpers with more than one pin are numbered. When setting the jumpers, ensure that the jumper caps are placed on the correct pins.

The illustrations show a 2-pin jumper. When the jumper cap is placed on both pins, the jumper is SHORT. If you remove the jumper cap, or place the jumper cap on just one pin, the jumper is OPEN.

SHORT OPEN

This illustration shows a 3-pin jumper. Pins 1 and 2 are SHORT

79

Image 85
Contents Ixtreme M5850 Service Guide Revision History Date Chapter UpdatedCopyright Conventions Preface Hardware Specifications and Configurations Block DiagramSetup Utility Menus Standard Cmos FeaturesIntroduction Introducing the MotherboardFeatures Integrated I/O Bios FirmwareLabel Component Mainboard ComponentsBlock Diagram Icon Component Description Ixtreme M5850Rear view Color/Use Headphone Audio Jack Function Table1CH Component Description Port IntroductionMouse PS/2 or USB, manufacturing option System PeripheralsKeyboard PS/2 or USB, manufacturing option SpeakersCard Reader Option Bios Hotkey List Hardware Specifications and ConfigurationsSpecification Main Board Major ChipsCache Memory System MemoryVideo Interface Audio InterfaceIDE Interface Power ManagementUSB Port Devices Idle Shut DownDevice Standby Mode Power Management Function Acpi support functionGlobal Standby Mode Suspend ModeAbout the Setup Utility Using BiosStandard Configuration Entering the Setup UtilityBios Navigation Keys Bios Setup UtilityMainDate and Time Using Bios Updating the BiosClock to All DIMM/PCIE Disabled Bios Setup UtilityAdvancedMiscellaneous Bootup Num-lock On Spread Spectrum EnabledUSB Beep Message Disabled Advanced Chipset ConfigurationOnboard Sata Mode Ahci Onboard Sata Controller EnabledOnboard USB Controller Enabled Legacy USB Support EnabledOnboard Audio Controller Enabled Onboard Graphics Controller EnabledOnboard LAN Controller Enabled Onboard LAN Option ROM DisabledSmart Fan Enabled System Component CharacteristicsBios Setup UtilityPower Supervisor Password Not Installed Bios Setup UtilitySecurityUser Password Change Supervisor Password Press Enter1st Boot Device/2nd Boot Device/3rd Boot Device Bios Setup UtilityBoot optionsSet Priority Order EFI Device Priority Press EnterOptical Disk Drive Priority Press Enter Hard Disk Drive Priority Press EnterQuiet Boot Enabled Fast Boot DisabledRemovable Device Priority Press Enter Network Device Priority Press EnterBios Setup UtilityExit Machine Disassembly and Replacement Before You Begin General InformationOpening the chassis Standard Assembly ProcessRemoving front bezel and HDD Cage Page Install the PSU Setting the Motherboard Page DIMM4 DIMM2 DIMM3 DIMM1 Assembly motherboard Insert the ODD/HDD SKU without HDD Carrier ODDRemove the HDD Carrier Install the HDD devices HDD Carrier Installed on SATA3 Master HDD Installed on SATA0 Insert Add-on card Close the Front BezelPage Page Connect Pata power cable Fix the screw Close the bracket Install system fan Overview Opening the computer Standard Disassembly ProcessRemoving the Front Bezel Removing the Add-on Card Page Removing the HDD Page Removing the ODD Removing the Main Board Removing the System FanPage Page Removing the power-supply Removing the HDD in HDD Carrier Removing Front IO/POWER Swtich PCB/TOP USB/CARD Reader Page Page Remove Power Swtich PCB Page Troubleshooting Power-On Self-Test Post KB-5 Initializes DMAC-1 & DMAC-2 Needed Bios Messages Action/FRU Post Error Messages ListSpecifics about the type and location of the memory error Error Symptom Action/FRU Processor / Processor Fan Error Symptoms ListMain board and Memory Hard Disk DriveAudio Error Symptom Action/FRU CD/DVD-ROM DrivePower Supply Error Symptom Action/FRU Video and MonitorParallel/Serial Ports KeyboardOther Problems Error Symptom Action/FRUUndetermined Problems Safety Precautions Jumper and Connector InformationInstalling the Motherboard in a Case Choosing a Computer CaseSetting Jumpers Checking Jumper SettingsJumper Settings Checking Jumper SettingsJumper Type Description Setting Default IIIustration Connecting 24-pin power cable Connecting Case ComponentsPin Signal Name Sysfan Cooling Fan Power Connector Pin Signal Name FunctionATX12V ATX 12V Power Connector Pin Signal Name Power/Sleep/Message waiting LED Pin Signal Name FunctionReset Switch Power SwitchInstalling the Processor Installing HardwareBefore installing the Processor Following illustration shows CPU installation components CPU Installation ProcedureInstallation Procedure Installing Memory ModulesMemory Memory Bus Sata cable optional Sata power cable optional Installing Serial ATA Hard DrivesInstalling Add-on Cards Onboard PCI interface does not support 64-bit Scsi cards FAUDIO1 Front Panel Audio header Connecting Optional DevicesSPDIFOUT1 Spdif out headerOption Sata 1~6 Serial ATA connectorsFUSB1~4 Front Panel USB headers ChassisPB 30L w/ HDD carrier ME BOM FRU Field Replaceable Unit List Exploded DiagramRAYLED51 HDD-CARRIER- SPRING-PIN Lightbase Page ChassisPB 30L w/o HDD carrier ME BOM Oddbuttontop Oddbuttonbottom Page FRU List